NAS Codex › QNAP › QNAP status LED red: flashing red vs solid red, and what each means
QNAP status LED red: flashing red vs solid red, and what each means
QNAP's status LED uses red two ways, and they mean different things. A red light that flashes every half second is a degraded RAID. A red light that stays on is one of eight faults, from a full volume to a hardware self-test error. Here is QNAP's table and where to look for each.
Written against: QNAP Turbo NAS user manual LED table (QTS 4.2.x) and QTS 5.1.x documentation. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Flashing red every 0.5 sec: QNAP says the NAS is in degraded mode, with one member drive failed in RAID 1, 5 or 6. Back up, then replace the failed drive. Solid red: log in and check Storage & Snapshots and the system log: QNAP's causes include an invalid disk, a volume that is full or nearly full, a fan failure, a disk read/write error or bad sector, degraded read-only mode, or a hardware self-test error.
QNAP's red LED rows
From QNAP's NAS user manual (QTS 4.2.x, "Checking System Status (LED and Alarm Buzzer)"). Exact LED behaviour can differ by model; check your model's hardware user guide if it does not match.
Flashes red every 0.5 sec
"The NAS is in degraded mode (one member hard drive fails in RAID 1, RAID 5 or RAID 6 configuration.)"
Red (solid)
- "The hard disk drive is invalid."
- "The disk volume has reached its full capacity."
- "The disk volume is going to be full."
- "The system fan is out of function" (the manual notes the TS-119 does not support smart fan).
- "An error occurs when accessing (read/write) the disk data."
- "A bad sector is detected on the hard disk drive."
- "The NAS is in degraded read-only mode (2 member hard drives fail in a RAID 5 or RAID 6 configuration, the disk data can still be read.)"
- "Hardware self-test error."
Flashing red: degraded mode
One drive in the RAID group has failed and the group is running without its full redundancy. In QTS 5, the storage pool shows Warning (Degraded), which QNAP defines as one or more RAID groups with the status Degraded and not enough spare disks to rebuild them all.
- Back up anything not already backed up. Another drive failure now could cost the pool.
- Find the failed drive under Storage & Snapshots > Storage > Disks/VJBOD.
- Replace it using QNAP's procedure on the S.M.A.R.T. warning page. If the rebuild does not start, see rebuild not starting.
Solid red: find which fault
Log in and check, in this order:
- Storage & Snapshots > Storage > Storage/Snapshots. A pool in Warning (Read-Only) is the most serious case: QNAP defines it as a RAID group in the pool being Not Active. Go straight to degraded read-only and back up. A volume that is full or nearly full also shows here.
- Disks/VJBOD > Disks. A disk with health Error ("The system has detected I/O errors. You must replace the disk immediately.") or Warning (S.M.A.R.T. errors detected) covers the read/write error and bad sector rows. See medium error.
- The system log and the fan. Look for fan or hardware alerts. QNAP's buzzer table pairs a fan failure with three short beeps and one long beep every 5 minutes.
If none of those shows a problem and the LED stays red, the remaining causes in QNAP's table are an invalid disk or a hardware self-test error, which are QNAP support cases.
Do not silence it and forget it
QNAP's manual warns that turning off the buzzer means you will not hear fan, capacity or degraded-mode alerts. In QTS 5.1 the audio alert options are under Control Panel > System > Hardware > Audio Alert, where "System events" triggers an audio alert when errors or warnings occur.
When to stop and get help
Stop and back up if the pool shows Warning (Read-Only) or Not Active, or if more than one drive shows Warning or Error health. QNAP's guidance for a RAID group that has gone Not Active is to contact support without changing or removing disks.
Questions
What does a flashing red status light mean on a QNAP?
QNAP's LED table says flashing red every 0.5 sec means the NAS is in degraded mode, with one member hard drive failed in a RAID 1, RAID 5 or RAID 6 configuration.
What does a solid red status light mean on a QNAP?
QNAP lists an invalid disk, a volume full or nearly full, a fan failure, a disk read/write error, a bad sector, degraded read-only mode, or a hardware self-test error.
Where do I turn the QNAP alert sounds on or off?
In QTS 5.1, Control Panel > System > Hardware > Audio Alert. QNAP's manual warns that disabling alerts means you will not hear fan, capacity or degraded-mode warnings.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-13.