NAS Codex › QNAP › QNAP "RAID group X is degraded, the RAID group has been set to read-only"
QNAP "RAID group X is degraded, the RAID group has been set to read-only"
QNAP has logged RAID group X is degraded, the RAID group has been set to read-only. Back up all the files immediately. and the status reads Warning (Degraded - Readonly). QNAP calls this a dangerous state. The order of the next steps matters more here than on any other storage warning.
Written against: QTS and QuTS hero (QNAP FAQ last modified 2023-07-28; QTS 5.0.x and 5.1.x documentation). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Copy your data off now, without changing any disk. QNAP's FAQ says the RAID group may become Not Active at any moment, and that replacing the faulty disk usually does not fix the read-only state and can make the group inactive. QNAP's order is: back up all data to another device, then replace the faulty disks, then reinitialize the NAS and copy the data back.
The message and the status
RAID group X is degraded, the RAID group has been set to read-only. Back up all the files immediately.The status shown is Warning (Degraded - Readonly). On the storage pool screen, QNAP's QTS 5 documentation also uses Warning (Read-Only), which it defines as: "One or more RAID groups in the storage pool have the status Not Active." It adds: "It might be possible to recover some data from volumes and LUNs."
Why the NAS did this
QNAP's FAQ describes the read-only state as a volume that is barely mounted, or a RAID group in a dangerous state that may become Not Active at any moment. It says this can happen when the number of faulty disks exceeds the RAID group's fault tolerance. Read-only is the NAS protecting what is left: it can still serve files, so this is the window to copy them.
For comparison, QNAP's storage pool states are:
| Pool status | QNAP's description |
|---|---|
| Ready | The storage pool is working normally. All RAID groups in the pool have the status Ready. |
| Warning (Degraded) | One or more RAID groups have the status Degraded. There are not enough spare disks available to rebuild all of them. |
| Warning (Rebuilding) | One or more RAID groups have the status Degraded (Rebuilding). QTS is rebuilding them due to disk failure. |
| Warning (Read-Only) | One or more RAID groups in the storage pool have the status Not Active. |
Plain Degraded is a pool that can still be rebuilt. Read-only is past that point.
Step 1: Back up, and change nothing
Do not replace, remove or reorder any disk yet. QNAP says replacing the faulty disk usually does not solve this and may make the RAID group inactive.
- Copy everything you need to another device: a USB disk, another NAS or a cloud backup. Start with the data you cannot replace, because the group could stop responding at any time.
- Avoid anything that writes heavily to the NAS or stresses the disks while you copy, such as starting a scrub, a bad block scan or a firmware update. (QNAP's firmware documentation separately recommends backing up all data before any firmware update.)
Step 2: Replace the faulty disks
Only after the backup is complete, replace the faulty disks. Use Storage & Snapshots > Storage > Disks/VJBOD to confirm which bays hold disks in Warning or Error health. QNAP's health definitions: Warning means S.M.A.R.T. errors were detected; Error means I/O errors were detected and the disk must be replaced immediately.
Step 3: Reinitialize and restore
QNAP's FAQ then says to reinitialize the NAS and copy the data back. Reinitializing erases what is on the disks, which is why the backup in step 1 has to be complete and checked first.
If the group becomes Not Active before you finish
QNAP's FAQ has a separate procedure for the alert RAID x - Not Active: confirm no disks were replaced or removed, log in as an administrator, go to Storage & Snapshots > Storage > Storage/Snapshots, double-click the pool or static volume and choose Manage > Recover RAID Group. If recovery fails, QNAP says to contact its support through the Service Portal and not to change or remove the disks.
When to stop and get help
If File Station can no longer reach the data, or the group has gone Not Active and Recover RAID Group does not bring it back, stop. QNAP's instruction is to contact support without changing or removing the disks. If the data is valuable and not backed up, a professional recovery service is the next call, not more attempts on the NAS.
Questions
What does Warning (Degraded - Readonly) mean on a QNAP NAS?
QNAP says the RAID group is in a dangerous state and could become Not Active at any moment, which can happen when the number of faulty disks exceeds the RAID group's fault tolerance. Back up all files immediately.
Should I replace the failed disk first?
No. QNAP's FAQ says replacing the faulty disk usually does not solve the read-only state and can make the RAID group inactive. Back up first, then replace the disks and reinitialize the NAS.
What if the RAID group shows Not Active?
QNAP's procedure is Storage & Snapshots > Storage > Storage/Snapshots, select the pool, then Manage > Recover RAID Group, after confirming no disks were changed. If that fails, contact QNAP support and do not change or remove the disks.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-13.
- QNAP FAQ: What should I do if I see a disk error or storage related warning message? (last modified 2023-07-28)
- QNAP QTS 5.0.x documentation: Storage Pool Status
- QNAP QTS 5.1.x documentation: Storage pool status
- QNAP QTS 5.1.x documentation: Disk statuses
- QNAP QTS 5.1.x documentation: Updating the firmware manually