NAS Codex › QNAP › QNAP beep codes: one long, two long, three short and one long
QNAP beep codes: one long, two long, three short and one long
QNAP NAS units talk through a buzzer. QNAP's user manual has a table of patterns, and its boot-troubleshooting FAQ uses two of them to diagnose a NAS that will not start. This page collects both.
Written against: QNAP Turbo NAS user manual buzzer table (QTS 4.2.x), QNAP FAQ last modified 2026-07-13, QTS 5.1.x audio alert settings. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
One short beep: start-up, shutdown, reset or a finished firmware update. One long beep: the NAS is on and ready (or a forced shutdown). Two long beeps: a volume nearly or completely full, degraded mode, or a rebuild starting. Three short and one long, repeating every 5 minutes: system fan failure. When booting, QNAP expects a short beep about 5 to 10 seconds after power-on and a long beep within five minutes; a missing beep points to a specific fault.
QNAP's buzzer table
From QNAP's NAS user manual (QTS 4.2.x, "Checking System Status (LED and Alarm Buzzer)"). Patterns can vary by model, so treat your model's hardware user guide as final.
| Pattern | What QNAP says it means |
|---|---|
| One short beep (0.5 sec) | The NAS is starting up; it is being shut down by software; the reset button was pressed; or a firmware update has completed. |
| Three short beeps | Data cannot be copied from the front USB port to external storage. |
| Three short beeps and one long beep, every 5 minutes | The system fan has failed. |
| Two long beeps (1.5 sec) | A volume is nearly full or full; the NAS is in degraded mode; or a user has started a rebuild. |
| One long beep | The NAS was shut down by force (hardware shutdown), or it is on and ready. |
The boot beeps QNAP uses to diagnose a NAS that will not start
QNAP's FAQ "My NAS doesn't power on or boot" (all NAS series) relies on two beeps:
- The short beep. "Does the NAS produce a short beep about 5 to 10 seconds after being powered on?" If not, QNAP calls it Problem #2: the NAS does not pass the POST (Power-On Self-Test), and points to the motherboard or RAM. Contact QNAP or your reseller.
- The long beep. "Within five minutes after powering on your NAS, you should hear a long beep (about 1.5 seconds long)." If not, QNAP calls it Problem #3: corrupted firmware image, likely caused by power loss during a firmware update, and points to its firmware recovery guide.
- Both beeps, but no QTS. If you hear the long beep after five minutes but cannot reach QTS with the disks installed, QNAP calls it Problem #4, a non-hardware issue, and says to contact QNAP.
Before relying on these, QNAP's initial checks are to power off, remove all drives (including M.2 SSDs), PCIe cards and USB devices, and put back the original RAM if you changed it. More on this on won't boot after a firmware update.
What to do for each warning pattern
Three short, one long, every 5 minutes (fan)
QNAP's LED table pairs a failed system fan with a solid red status LED. Check the fan, and the temperatures in QTS, before the NAS runs hot. See status LED red.
Two long beeps
Log in and open Storage & Snapshots. If a volume is full, free space. If the pool shows Warning (Degraded), a member disk has failed: back up, then replace it. If you just started a rebuild, the beeps confirm it.
Turning the alerts on or off
In QTS 5.1, QNAP puts the settings at Control Panel > System > Hardware > Audio Alert. "System operations" triggers an audio alert every time the NAS starts, shuts down or upgrades firmware. "System events" triggers one when errors or warnings occur. QNAP's older manual warns that turning off the buzzer means you will not hear fan, capacity or degraded-mode alerts, so leave "System events" on.
When to stop and get help
If the NAS beeps for a degraded pool and a second disk also shows a warning, or there is no short beep at all after power-on, stop. The first needs a backup before anything else; the second is a hardware fault for QNAP or your reseller.
Questions
What does three short beeps and one long beep mean on a QNAP?
In QNAP's buzzer table, three short beeps and one long beep repeating every 5 minutes means the system fan has failed.
What do two long beeps mean on a QNAP?
QNAP's table says a volume is nearly full or full, the NAS is in degraded mode, or a user has started a rebuild.
My QNAP makes no beep when I power it on. What does that mean?
QNAP's boot FAQ says the NAS should give a short beep about 5 to 10 seconds after power-on. If it does not, it has not passed the POST, which points to the motherboard or RAM.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-13.