NAS Codex › QNAP › QNAP NAS won't boot after a QTS firmware update
QNAP NAS won't boot after a QTS firmware update
The firmware update ran, the NAS restarted, and it never came back. QNAP's FAQ for exactly this case starts with one test that splits the problem in two: does the NAS boot with its storage drives removed?
Written against: All QNAP NAS series (QNAP FAQs last modified 2023-01-11 and 2026-07-13). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Label each drive with its bay number, power off, remove the storage drives and boot the NAS again. If it now boots, QNAP says the drives are the likely problem, and the firmware can be updated over SSH (an advanced procedure on QNAP's page). If it still will not boot and there is no long beep within 4 minutes, QNAP says the NAS itself is likely faulty: try QNAP's firmware recovery guide where your model supports it, or contact QNAP.
Before you pull anything
Label every drive with its bay number before removing it, and put each one back in the same bay. QNAP's related LED FAQ says the same: "Before removing the disks, label each disk slot clearly, such as Disk 1, Disk 2, and so on." When QNAP's procedures put disks back, they go back in their original order.
Step 1: Boot without the drives
QNAP's solution begins: "remove the storage drives and attempt to boot the NAS again." It refers you to your model's user guide in the QNAP Download Center for how to remove them on your hardware.
Step 2: Read the result
It still does not boot
QNAP: "If the NAS doesn't emit a long beeping sound within 4 minutes", the NAS itself is the likely problem. QNAP points to its Firmware Recovery Guide, and notes that not all models support firmware recovery. For many x86 models QNAP publishes a NAS Recovery Guide for x86-based NAS, which rewrites the NAS boot device from a bootable USB drive and then updates the firmware with Qfinder Pro. It is done with the storage drives out, and QNAP notes that if the drives are not new, the firmware must be updated again after they are installed.
It boots without the drives
Then QNAP says the drives are the likely issue, not the NAS. Its FAQ gives a procedure that begins "Connect to the NAS via SSH" and updates the firmware from the command line. That procedure assembles and mounts a system partition by hand. It is beyond what this page will walk you through: if you are not comfortable at a Linux shell, use QNAP support instead. If you do follow it, copy the commands exactly from QNAP's page for your model, not from forums.
The beeps QNAP uses to diagnose boot problems
QNAP's general "doesn't power on or boot" FAQ, which applies to all NAS series, sets out the same checks by sound:
| QNAP's problem | How QNAP says to recognise it | QNAP's next step |
|---|---|---|
| Problem #1: The NAS does not power on. | Check if the LEDs on the front panel turn on after pressing the power button. | Try another outlet; then contact QNAP or your reseller. |
| Problem #2: The NAS does not pass the POST (Power-On Self-Test). | No short beep about 5 to 10 seconds after being powered on. | Likely motherboard or RAM; contact QNAP or your reseller. |
| Problem #3: Corrupted firmware image. | No long beep (about 1.5 seconds long) within five minutes after powering on. | Follow QNAP's firmware recovery guide; contact QNAP if it fails. |
| Problem #4: Non-hardware issue. | None of the first three, and a long beep after five minutes, but QTS cannot be reached with the disks installed. | Contact QNAP. |
QNAP's FAQ names power loss during a firmware update as the likely cause of a corrupted firmware image, and QNAP's manual firmware update FAQ strongly recommends connecting the NAS to an uninterruptible power supply (UPS). Its initial checks for any boot problem are to power off, remove all drives (including M.2 SSDs), PCIe cards and USB devices, put back the original RAM if you changed it, and power on.
When to stop and get help
If the NAS will not boot even without drives and your model is not covered by QNAP's recovery guides, it needs QNAP repair. Keep the drives labelled and out of it. If the NAS boots without drives but not with them, and the data is not backed up, do not experiment with the drives in another machine: contact QNAP support first.
Questions
Why won't my QNAP boot after a firmware update?
QNAP's FAQ says to remove the storage drives and boot again. If it boots, the drives are the likely issue; if there is no long beep within 4 minutes even without drives, the NAS itself is likely at fault.
What does no long beep after power-on mean on a QNAP?
QNAP's boot FAQ says you should hear a long beep, about 1.5 seconds, within five minutes of powering on. If you do not, it points to a corrupted firmware image and QNAP's firmware recovery guide.
Will removing the drives erase my data?
Removing drives does not erase them, but label each with its bay number and put it back in the same bay. QNAP's own LED FAQ asks you to label each disk slot before removing the disks.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-13.
- QNAP FAQ: Why won't my NAS boot after a firmware update? (last modified 2023-01-11)
- QNAP FAQ: My NAS doesn't power on or boot. How can I fix this? (last modified 2026-07-13)
- QNAP FAQ: NAS Recovery Guide for x86-based NAS
- QNAP FAQ: Where can I download firmware and update it manually? (last modified 2026-01-06)
- QNAP FAQ: NAS cannot be accessed and the Status LED is flashing green (last modified 2026-06-16)