NAS Codex › QNAP › QNAP firmware update error FW004: "A flash read/write error occurred"

QNAP firmware update error FW004: "A flash read/write error occurred"

You tried to update QTS and got: Failed to update system. A flash read/write error occurred. Error code: FW004. QNAP documents this for a specific list of older models running QTS 4.3.6.1070 or older when updating to QTS 4.4.1 or later. QNAP's fix is to step through an intermediate firmware image first.

Written against: QTS 4.3.6.1070 or older, updating to QTS 4.4.1 or later (QNAP FAQ last modified 2025-12-22). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

Check that your model is on QNAP's list below. If it is, download the initial QTS 4.3.6 firmware image QNAP lists for your model, install it as a manual update, then use Live Update to reach the current firmware. Back up first, keep the NAS on stable power, and do not power it off during any update.

The message

Failed to update system. A flash read/write error occurred. Error code: FW004

QNAP's FAQ gives the scenario as updating the firmware to "QTS 4.4.1 or later". The FAQ does not give a root cause; it gives a route around it.

Is your NAS affected?

QNAP lists the applicable firmware as "QTS 4.3.6.1070 or older" on these models:

SeriesModels listed by QNAP
TS-x31P / x31+TS-131P, TS-231P, TS-231+, TS-431P, TS-431+, TS-531P
TS-x31P2TS-231P2, TS-431P2
TS-x31X / X2TS-431X, TS-431X2, TS-531X, TS-831X
Rackmount x31TS-431U, TS-431XU, TS-431XeU, TS-431XU-RP, TS-831XU, TS-1231XU, TS-1231XU-RP
x32XTS-432XU, TS-832X, TS-832XU
OtherTS-1635, QBoat Sunny

If your model is not on the list, or your QTS version is newer than 4.3.6.1070, this FAQ is not about your NAS. Read QNAP's general firmware pages instead (linked under Sources).

Before you start

QNAP's firmware documentation: "To prevent data loss, QNAP recommends backing up all data on your device before updating the firmware." And: "Do not power off your device during the firmware update process." QNAP also strongly recommends connecting the NAS to an uninterruptible power supply (UPS). If any storage pool is degraded, deal with that first; do not update firmware on a degraded pool.

QNAP's fix

  1. Find your model in the table on QNAP's FW004 FAQ and download the initial QTS 4.3.6 firmware image listed for it. Take the image from QNAP's own page for your exact model, not from anywhere else.
  2. Install that image as a manual firmware update.
  3. Then run Live Update to bring the NAS to the current firmware.

How a manual firmware update is done

QNAP's manual update FAQ gives the menu path as Control Panel > System > Firmware Update. Its QTS 5.1 documentation gives the steps below. The affected models run QTS 4.3.6, where screen labels may differ; if they do not match, follow the manual update FAQ rather than guessing:

  1. Download and extract the firmware package for your model.
  2. Go to Control Panel > System > Firmware Update > Manual Installation.
  3. Click Browse and select the extracted file.
  4. Click Update System. A confirmation window appears.
  5. Click OK. The device restarts.

QNAP notes the update may take several minutes or longer, depending on the hardware configuration and network connection. Wait for the NAS to come back before doing anything else.

If the NAS does not come back

A NAS that will not boot after a firmware update has its own QNAP FAQ. See QNAP won't boot after a firmware update.

When to stop and get help

If the intermediate image also fails to install, or the NAS does not finish booting afterwards, stop updating and contact QNAP support. Repeated attempts on a NAS whose data is not backed up are not worth the risk.

Questions

What causes QNAP error FW004?

QNAP's FAQ does not state a root cause. It documents the error for specific models on QTS 4.3.6.1070 or older when updating to QTS 4.4.1 or later.

How do I fix FW004?

Download the initial QTS 4.3.6 firmware image QNAP lists for your model on its FW004 FAQ, install it as a manual update, then use Live Update to reach the current firmware.

Where is the manual firmware update in QTS?

Control Panel > System > Firmware Update. In QTS 5.1 the tab is Manual Installation: click Browse, select the file, click Update System, then OK.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-13.