NAS Codex › Synology › Synology storage pool "Degraded": how Synology says to repair it
Synology storage pool "Degraded": how Synology says to repair it
Storage Manager shows a storage pool as Degraded. Synology defines it this way: a pool "becomes Degraded when one or more of its drives becomes defective, but the storage pool remains accessible because no data loss has occurred." The pool still works, but it is running with a defective drive. The fix is to replace the bad drive and run Repair, in the order below.
Written against: Synology DSM 7 help (Storage Manager: Repair a Storage Pool) and Knowledge Center articles tagged DSM 7 series and DSM legacy versions. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Back up first. Then in Storage Manager > Storage, select the Degraded pool, check which drive is defective on the HDD/SSD page, replace it with a healthy drive at least as large as Synology's size rule requires, go back to the pool and choose Repair from the upper-right menu. Repair only exists for pools with data protection (RAID 1, 5, 6, 10, F1, and SHR with two or more drives).
Where else you will see it
- The NAS may beep: Synology's beeping article lists "the volume has degraded" as a reason under Control Panel > Hardware & Power > General > Beep Control. See NAS keeps beeping.
- The STATUS light may go orange: Synology's LED article lists "Degraded volume detected" as a probable cause. See STATUS LED orange.
Before you start
- Repair only works on pools with data protection: RAID 1, RAID 5, RAID 6, RAID 10, RAID F1, and SHR with at least two drives.
- If a hot spare is assigned to the pool, Synology says it will repair the degraded pool automatically.
- Synology recommends drives from its Products Compatibility List and warns that other drives may affect stability and result in data loss.
How big the replacement drive must be
- RAID 1, 5, 6, 10, F1: equal to or larger than the smallest drive in the pool.
- SHR-1: equal to or larger than the failed drive, or equal to or larger than the second-largest drive in the pool. Synology's example: in a pool of 3 TB, 2 TB, 2 TB and 1 TB drives, a failed 3 TB drive can be replaced with a 2 TB or larger drive.
- SHR-2: equal to or larger than the failed drive, or equal to or larger than the fourth-largest drive in the pool.
Synology's repair steps (DSM 7)
- Go to Storage Manager > Storage and select the pool in Degraded status.
- Expand the pool information and check the drive status.
- Go to the HDD/SSD page to confirm which drive is defective.
- Remove the defective drive and install a healthy one. If your model does not support hot-swapping, power it off first. Synology notes that all existing data on the replacement drive will be erased.
- Return to the Storage page and select the degraded pool.
- Click the upper-right icon and select Repair. The Repair option only appears when a pool is degraded.
Why the repair takes so long
Synology gives two reasons. By default the system lowers the repair speed so other services keep running; you can raise it by adjusting the Resync speed. If that does not help, a drive in the pool may have problems: check health under Storage Manager > HDD/SSD.
Fast Repair (on by default, under Storage Manager > Storage > Global Settings > Advanced Repair Settings) skips unused space. Synology says that if pool usage exceeds 80%, the system switches to Regular Repair automatically. Auto Repair (off by default) repairs the pool once a replacement goes into the same slot, but it is not supported on SHR pools and only exists on models that support RAID Group.
When to stop and get help
Stop if a second drive in the same pool shows Warning, Critical or Failing, if the pool changes to Crashed (Synology says you can no longer repair a crashed pool yourself; see volume crashed), or if the Repair option cannot be selected. Back up before any further step.
Questions
Is my data still there when a Synology pool is Degraded?
Synology says a degraded pool remains accessible because no data loss has occurred. It is running with a defective drive, so back up before replacing anything.
Can I use a smaller replacement drive?
For RAID 1, 5, 6, 10 and F1 the replacement must be at least the size of the smallest drive in the pool. SHR has its own rules based on the failed drive or the second-largest (SHR-1) or fourth-largest (SHR-2) drive.
Why is the Repair option missing?
Synology says Repair only appears when a pool is degraded, and only for pools with data protection: RAID 1, 5, 6, 10, F1, or SHR with at least two drives.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-14.
- Synology DSM 7 help: Repair a Storage Pool
- Synology Knowledge Center: Why does it take a long time to repair a storage pool?
- Synology Knowledge Center: My Synology NAS keeps beeping. What can I do?
- Synology Knowledge Center: The STATUS or ALERT LED indicator keeps blinking or lights up steadily in orange