NAS Codex › Synology › Synology NAS keeps beeping: find the "Reason for current beep" and stop it safely
Synology NAS keeps beeping: find the "Reason for current beep" and stop it safely
A Synology NAS that keeps beeping is telling you about a fault, and DSM records which one. Synology does not publish a beep-code table for this; instead, DSM shows a Reason for current beep in Control Panel. Find that reason first, deal with it, and only then mute the beeping.
Written against: Synology Knowledge Center articles tagged DSM 7 series and DSM legacy versions (Mute in DSM 7.0 and above, Beep Off in DSM 6.2 and earlier). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Sign in to DSM and check Notifications (upper-right of the desktop). Then go to Control Panel > Hardware & Power > General > Beep Control and read Reason for current beep. Synology lists four common reasons: a degraded volume, a crashed volume, an abnormal SSD cache and a malfunctioning cooling fan. To silence it, click Mute (DSM 7.0 and above) or Beep Off (DSM 6.2 and earlier).
Step 1: find the reason
- Sign in to DiskStation Manager (DSM).
- Open Notifications at the upper-right corner of the desktop and look for likely causes.
- Go to Control Panel > Hardware & Power > General > Beep Control and look at Reason for current beep.
Step 2: act on the reason
Reason: the volume has degraded
Synology points to its storage pool repair help. A degraded pool has a defective drive but no data loss yet; back up, replace the drive and run Repair. Full steps: storage pool degraded.
Reason: the volume has crashed
Synology points to its volume crash article. If you can still read your files, do not power the NAS off; copy the data to a computer on your network first. Full steps: volume crashed.
Reason: the SSD cache is abnormal
Synology points to its SSD cache FAQ. Note that Synology lists a crashed or improperly unmounted SSD read-write cache among the causes of a volume crash, so treat an abnormal cache seriously and back up.
Reason: the cooling fan is malfunctioning
Synology's steps: dust the NAS first, and make sure it sits somewhere with an appropriate temperature. If the problem continues, the fan may be broken, and Synology points to its warranty claim process.
Step 3: silence it
- Go to Control Panel > Hardware & Power > General > Beep Control and click Mute (DSM 7.0 and above) or Beep Off (DSM 6.2 and earlier).
- If the Mute or Beep Off button is turned off, Synology says to reboot the NAS and try again.
Muting stops the sound, not the fault. If the STATUS light is also orange, see STATUS LED orange.
Beeps that are not a fault
Synology's own articles mention a few normal beeps. In its boot test with drives and external devices removed, a beep within three minutes with a static Power LED means the motherboard is working. Pressing the RESET button for about 4 seconds gives one beep (a Mode 1 reset of the admin login and network settings); a Mode 2 reset adds three more beeps. If you hear these after pressing RESET, the beeping is the reset, not a fault.
When to stop and get help
Stop and back up if the reason is a crashed volume or an abnormal SSD cache, or if a degraded volume appears together with a second drive in Warning or worse. Do not mute and forget a degraded volume: it stays degraded until the defective drive is replaced and the pool is repaired.
Questions
Is there a Synology beep code table?
Synology's beeping article does not give one. It tells you to read Reason for current beep under Control Panel > Hardware & Power > General > Beep Control, and to check Notifications.
How do I stop my Synology NAS beeping?
Control Panel > Hardware & Power > General > Beep Control, then Mute (DSM 7.0 and above) or Beep Off (DSM 6.2 and earlier). If the button is turned off, reboot and try again. Fix the reason as well.
My Synology beeps because of the fan. What does Synology say?
Dust the NAS and make sure the room temperature is appropriate. If the issue persists, the fan may be broken; Synology points to its warranty claim article.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-14.
- Synology Knowledge Center: My Synology NAS keeps beeping. What can I do?
- Synology DSM 7 help: Repair a Storage Pool
- Synology Knowledge Center: What can I do if one of my volumes crashed?
- Synology Knowledge Center: What causes a volume to crash?
- Synology Knowledge Center: My Synology storage system cannot boot up and the Power LED indicator keeps blinking
- Synology Knowledge Center: How do I reset my Synology NAS? (For DSM 6.2.4 or above)