NAS Codex › Synology › Synology NAS cannot enter "Ready" status after installing drives: Synology's drive-by-drive check
Synology NAS cannot enter "Ready" status after installing drives: Synology's drive-by-drive check
The NAS powers on with its drives installed and the Power LED is normal, but Synology Assistant never shows it as Ready. Synology's article for this case says the cause is a drive: during startup the system checks the system partition on every installed drive, and any abnormality it finds keeps the NAS out of Ready. The fix is to find the problem drive by starting the NAS on one drive at a time. This page gives Synology's steps in order.
Written against: Synology Knowledge Center article for DSM 7.0 and above and DSM 6.2 and below, models with 2 or more drive bays. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Synology's method: power off, remove all drives, put one drive in the Drive 1 slot and power on. The Power LED should turn static blue or green within 10 minutes; then check Synology Assistant. Repeat with each drive to find the ones that will not reach Ready. On hot-swap models, once a drive reaches Ready, reinsert the others and use Online Assemble in Storage Manager. Replace any drive that is not healthy and repair the storage pool.
Check that this is the right page
Synology's article applies to models with 2 or more drive bays, and it assumes the Power LED is in a normal state: lit steadily in blue or green. If the Power LED keeps blinking instead, Synology sends you to a different article; see Power LED blinking, won't boot.
Synology Assistant's statuses mean different things. Synology defines Ready as DSM installed and ready to use. Not installed on drives you have been using for some time means the device cannot recognize the drives. Configuration lost and Migratable are separate cases with their own steps; see Configuration lost.
Why one drive can stop the whole NAS
Synology explains that the startup process checks the system partition on each installed drive. If any abnormality is detected, the system will not enter Ready status. Its resolution is to identify the problematic drives and use the remaining drives to power on the system.
DSM 7.0 and above: models that support hot-swapping
Synology says to check your model's datasheet to see whether it supports hot-swapping drives. If it does:
- Power off the NAS.
- Remove all the drives.
- Insert one of the drives in the slot for Drive 1.
- Power on and watch the Power LED. It should change to static blue or green within 10 minutes.
- Open Synology Assistant and check the device status. If it shows Ready, go to step 6. If not, long-press the power button to shut the NAS down and repeat steps 3 to 5 with another drive until one works. If no drive works, Synology suggests using a spare drive (see below).
- In DSM, go to Storage Manager > Storage. The storage pool should show as Missing.
- Follow the Suggestion shown under the missing storage pool and install the other drives back.
- Find the Available Pool on the Storage page and run Online Assemble, either from the link in the pool's expanded information or from the pool's upper-right ellipsis menu.
- When the online assemble finishes, check the drive statuses. Replace any drive that is no longer healthy and repair the storage pool.
DSM 7.0 and above: models that do not support hot-swapping
- Power off the NAS and remove all the drives.
- Insert one drive in the slot for Drive 1.
- Power on; the Power LED should turn static blue or green within 10 minutes.
- Check Synology Assistant. The NAS should be in Ready status.
- Long-press the power button to shut it down.
- Repeat with each drive, and note which drives do not let the NAS power on and enter Ready.
- If the number of failing drives is less than or equal to the number of drive failures your storage pool's RAID type can tolerate: install all the drives that worked, power on, and check that Synology Assistant shows Ready. If it still does not, or if more drives failed than the RAID type tolerates, Synology suggests a spare drive.
- Go to Storage Manager > Storage and check the pool and drives. If any drive is not healthy, Synology's order is: back up your data, remove the storage pool, create a new one using only healthy drives, and restore the backup. If all drives are healthy, insert new drives to repair the pool, which should be in a Degraded status; see Storage pool Degraded.
On DSM 6.2 and below, Synology gives the same drive-by-drive steps as for non-hot-swap models, with the final check under Storage Manager > Storage Pool.
If no drive reaches Ready: the spare-drive method
Synology points to the multi-bay section of its data-recovery article. In short, as Synology describes it there:
- The storage pool should use a RAID type with data protection (RAID 1, 5, 6, 10, F1, or SHR with at least two drives). For Basic, JBOD, RAID 0 or one-drive SHR, Synology says you need at least one empty drive slot, or else to recover the data with a PC.
- Power off, remove all drives, put a spare drive in Drive 1 and install DSM on it. The DSM version must match the one on your NAS. Synology says not to use the spare drive to create storage pools or volumes.
- Power off, insert one of the original drives while keeping the spare in Drive 1, power on, and on DSM 7 use the Online Assemble link in Storage Manager to assemble the pool.
Synology notes that Online Assemble syncs the spare drive's system partition to the other drives in the pool. Its DSM 7 help page on assembling a storage pool adds three points. The Available Pool entry appears only when enough drives are installed for the pool's RAID configuration. You assemble it by expanding it on the Storage page, clicking Online Assemble and then Start; when it succeeds, the name changes from Available Pool to Storage Pool. If assembling fails, the status changes to Assemble failed, and Synology recommends restarting the system to assemble it.
When to stop and get help
Stop and get help if no drive reaches Ready and you have no spare drive, or if more drives fail the test than your RAID type can tolerate and the data is not backed up elsewhere. Do not create a storage pool on the spare drive; Synology says not to. Do not remove or recreate a pool until the data has been copied off. If you are unsure, contact Synology Technical Support before changing anything.
Questions
Why does my Synology NAS not enter Ready status?
Synology says the startup process checks the system partition on each installed drive, and any abnormality it detects stops the system from entering Ready. The fix is to find the problem drive by starting the NAS on one drive at a time in the Drive 1 slot.
How long should I wait after powering on with one drive?
Synology says the Power LED should change to static blue or green within 10 minutes. Then check the device status in Synology Assistant.
What does Online Assemble do in this case?
After the NAS reaches Ready on one drive and you reinsert the others, Synology says the storage pool shows as Missing and then, with the drives back, as an Available Pool that Online Assemble brings back as a Storage Pool. When a spare drive is used, Synology notes that it syncs the spare's system partition to the other drives in the pool.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-14.
- Synology Knowledge Center: My Synology NAS cannot enter "Ready" status after installing drives. What can I do?
- Synology Knowledge Center: What do the device statuses in Synology Assistant and Web Assistant mean?
- Synology Knowledge Center: How do I recover data from a Synology NAS that is no longer accessible?
- Synology DSM 7 help: Assemble a Storage Pool