NAS Codex › Synology › Synology NAS won't boot and the Power LED keeps blinking: Synology's checks

Synology NAS won't boot and the Power LED keeps blinking: Synology's checks

The NAS will not finish starting and the Power light just keeps blinking. Synology's normal Power LED is static (blue or green, depending on the model), and blinking normally means powering on or shutting down. If it never settles, Synology gives a test sequence that separates a dead motherboard or power supply from a drive, an add-on card or the power adapter.

Written against: Synology Knowledge Center articles tagged DSM 7 series and DSM legacy versions; LED system-mode tables for models released in 2015 or later running DSM 6.2.4 and later. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

Give it time first: Synology says a flashing Power LED means powering on or off, and to wait half an hour before trying again. If it is still blinking, power off, remove all drives and external devices, unplug the power cord for a few seconds, plug it back in and power on. A static Power LED with a beep within three minutes means the motherboard works and the problem is the drives, add-ons or adapter. Still blinking after 20 minutes with no drives: Synology says the motherboard or power supply may be faulty.

What the Power LED should do

Synology's boot-LED table (models from 2015, DSM 6.2.4 and later) shows the POWER light (blue or green) blinking while powering on and while shutting down, and static once DSM is not yet ready, ready, or in hibernation. Its connection article adds: a flashing Power LED means the device is powering on or off; wait half an hour, and if it keeps flashing, unplug the device, plug it back in and power on again. Synology's boot-LED notes also say the Power LED may keep blinking if the device runs into problems while shutting down.

1. Check the motherboard (no drives)

  1. Power off the NAS.
  2. Remove all attached external devices and all installed drives. Synology counts as external devices: Ethernet cables, USB devices, additional memory modules, expansion units, 10GbE network cards and M.2 SSD adapter cards. M.2 NVMe/SATA SSDs on the motherboard and eSATA drives also come out.
  3. Unplug the power cord, wait a few seconds, plug it back in, and power on.
  4. Check the power adapter's own LED. Blinking continuously or not responding: the adapter may be faulty or damaged. Static: go on.
  5. Check the NAS Power LED:
    • Still blinking or not responding after more than 20 minutes (or the power button does nothing): the motherboard or power supply may be faulty or damaged, and you may be eligible for a warranty claim.
    • Static, with a beep within three minutes: the motherboard is working. The problem is likely the drives, external devices or power adapter. Continue below.

2. Check the drives

Synology suggests booting with a spare drive. If it still fails, the cause is another component. If it boots normally, the original drives are the suspect: Synology's "cannot enter Ready status" article tests them one at a time in the Drive 1 slot to find the faulty one.

3. Check external devices

  1. Power off.
  2. Attach the external devices back one at a time.
  3. Power on and watch the Power LED. If it blinks for more than 20 minutes after adding a device, that device is the likely cause; Synology says to contact the reseller or distributor you bought from.

4. Check the power adapter

If the motherboard works but the NAS fails to boot with several drives installed, Synology says a defective adapter that cannot supply enough current may be the cause. Try a replacement adapter.

Your data while the NAS is down

Synology says that after a replacement unit arrives you can migrate the drives to it, and points to its data-recovery-with-a-PC article if you need the data urgently in the meantime.

When to stop and get help

Stop and contact the seller or Synology warranty service if the Power LED still blinks after 20 minutes with every drive and device removed. If the data on the drives is not backed up, keep the drives safe and do not install DSM onto them anywhere: Synology warns that installing DSM on a NAS showing Not installed deletes all data on the drives.

Questions

How long should a Synology Power LED blink at start-up?

Synology's connection article says to wait half an hour before trying to connect again. Its boot-failure article treats a Power LED still blinking after more than 20 minutes, with drives and devices removed, as a possible motherboard or power supply fault.

Does a beep mean my Synology motherboard is fine?

Synology says a beep within three minutes with a static Power LED indicates the motherboard is functioning properly, so look at the drives, external devices or power adapter next.

What counts as an external device for this test?

Synology lists Ethernet cables, USB devices, additional memory modules, expansion units, 10GbE network interface cards and M.2 SSD adapter cards, plus M.2 SSDs on the motherboard and eSATA drives.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-14.