NAS Codex › Synology › Synology NAS not found by find.synology.com or Synology Assistant: Synology's checks
Synology NAS not found by find.synology.com or Synology Assistant: Synology's checks
You cannot reach your Synology NAS from a computer on the same network, and neither Web Assistant (find.synology.com) nor the Synology Assistant desktop app lists it. Synology says this can happen after a change to the network, such as a new internet provider or router. Its checks run from the power light outwards; the RESET button comes last, and it matters which reset you do.
Written against: Synology Knowledge Center articles tagged DSM 7 series and DSM legacy versions (reset steps for DSM 6.2.4 and above). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Check the Power LED first (off, flashing, or on). If it is on, check the LAN port lights, run a PING from your computer, then search with Web Assistant (find.synology.com) and Synology Assistant from a computer on the same network and subnet. Only if that fails, press RESET for about 4 seconds until one beep. Synology says this resets the admin login and network settings and does not affect stored data, but it also locks encrypted folders and volumes on DSM 7.2 and earlier (see step 6).
1. Read the Power LED
- Off: the NAS is off. Boot it. If it will not boot, Synology says there may be a power, adapter or other hardware problem, and to contact the reseller for RMA if it is under warranty.
- Flashing: it is powering on or off. Wait half an hour, then try again. If it keeps flashing, unplug it, plug it back in and power on. Still flashing: see Power LED keeps blinking.
- On: it is powered on, so the problem is more likely the network. Continue.
If the STATUS light keeps flashing orange instead, see STATUS LED orange.
2. Check the network path
- Make sure the LED lights on the NAS's connected LAN ports are flashing normally. Synology notes some models have LAN port LEDs that do not show network status.
- Make sure the LED lights on your switch or router are flashing normally.
- Run a PING from your computer to the NAS to test the connection.
- Search for the NAS with Web Assistant (type find.synology.com into the browser address bar) and with Synology Assistant (Download Center > your model > Desktop Utilities).
3. If Web Assistant can't find it
- Make sure the NAS and your computer are both connected to the internet, and on the same local network and subnet.
- Try a different browser.
- If you can still reach DSM some other way: allow the NAS to appear in Web Assistant under Control Panel > Info Center > Device Analytics (Synology's troubleshooting article calls the setting Share Network Location; the DSM 7 Info Center help calls it Enable Web Assistant); and if you changed the server name during setup, Synology suggests changing it back to SynologyNAS under Control Panel > Network > General and trying again.
4. If Synology Assistant can't find it
- Same local network and subnet.
- Allow Synology Assistant through the DSM and Windows firewalls; temporarily disable antivirus software on the computer.
- Try other Ethernet cables, and another LAN port if the NAS has more than one. If DSM is not installed or you just did a Mode 2 reset, use a 1 GbE port rather than 10 GbE.
- Try Synology Assistant on another computer.
- With Synology Assistant 7.0-50044 or later and a NAS on DSM 6.2.3 or earlier, click the gear icon and enable Allow compatibility with devices that do not support password encryption.
5. Read the status it shows
- Not installed: Synology says do not proceed with the installation, or all your data will be deleted. Retrieve the data from the drives first.
- Configuration lost / Migratable: shared-folder data is not deleted when you reinstall DSM. See Configuration lost.
- Ready: DSM is installed and ready; double-click to open it.
- Connection failed (Synology Assistant only): a network configuration error. Double-click to configure the network, or reset the network settings with the RESET button.
6. Last resort: Mode 1 reset
Warning: Synology's list of Mode 1 effects goes beyond the login and network. On DSM 7.2 and earlier, encrypted shared folders are locked (a machine-key cipher is deleted from Key Manager), and encrypted volumes are locked because the Encryption Key Vault is erased, so you need each volume's recovery key. High-availability and Virtual Machine Manager clusters are removed. Have your recovery keys ready before you press RESET.
Press and hold RESET for about 4 seconds until you hear a beep, then release. Synology's reset article calls this Mode 1: it resets the admin login credentials and network settings (to DHCP) and disables firewall rules and Auto Block, but does not affect stored data. Afterwards the LAN IP may change and the admin password is reset. If the NAS does not beep, Synology says it could be a hardware failure. Do not press and hold RESET again within 10 seconds: holding it a second time for 4 seconds until 3 more beeps is a Mode 2 reset, which wipes all system configurations.
If you then connect the NAS straight to the computer without a router, it may take a 169.254.x.x address; set the computer's Ethernet to obtain an IP automatically (DHCP) and search with Synology Assistant again.
When to stop and get help
Stop if Synology Assistant shows Not installed on a NAS that held data, if the Power LED never stops flashing, or if the NAS does not beep when you press RESET (Synology: possible hardware failure; contact the reseller for RMA under warranty).
Questions
Does pressing RESET on a Synology delete my data?
A 4-second press until one beep is a Mode 1 reset: Synology says it resets admin login and network settings and does not affect stored data, though on DSM 7.2 and earlier it locks encrypted folders and volumes. Pressing again within 10 seconds for 3 more beeps is a Mode 2 reset, which wipes all system configurations.
Why can't find.synology.com see my NAS?
Synology lists: the NAS or computer is not online, they are on different networks or subnets, the browser, Share Network Location being off, or a changed server name. Try Synology Assistant as well.
What does "Connection failed" mean in Synology Assistant?
Synology says there is an error with the network configuration. Double-click the device to configure the network, or reset the network settings with the RESET button.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-14.
- Synology Knowledge Center: I can't connect to my Synology NAS on the local network. What can I do?
- Synology Knowledge Center: How do I find my Synology storage system via Web Assistant or Synology Assistant?
- Synology Knowledge Center: What do the device statuses in Synology Assistant and Web Assistant mean?
- Synology Knowledge Center: How do I reset my Synology NAS? (For DSM 6.2.4 or above)
- Synology DSM 7 help: Info Center (opened 2026-11-15)