NAS Codex › Synology › Synology Assistant shows "Configuration lost": find the cause before you reinstall DSM

Synology Assistant shows "Configuration lost": find the cause before you reinstall DSM

Synology Assistant or Web Assistant lists your NAS as Configuration lost and you cannot sign in. Double-clicking the NAS will offer to reinstall DSM. Synology says that reinstall keeps the data on your volumes, but it also says to find the cause first, because one of the causes is failing drives, and another is a malfunctioning RESET button.

Written against: Synology Knowledge Center articles tagged DSM 7 series and DSM legacy versions (reset steps for DSM 6.2.4 and above). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

If you just did a Mode 2 reset on purpose, this status is expected: double-click the NAS and reinstall DSM; Synology says volume data is not affected. If you did not press RESET, work out why first. Synology lists drives moved from a non-recommended or newer model, file system errors in the system partition (possibly damaged drives), a malfunctioning RESET button, and an accidental Mode 2 reset.

What "Configuration lost" means, per Synology

Synology's device-status article says the status "is usually the result of a Mode 2 Reset", and that you can double-click the device and reinstall DSM to get a fresh system without affecting the data in the volume. Its connection article agrees: for Configuration lost or Migratable, the data in shared folders is not deleted when you reinstall DSM.

A Mode 2 reset, per Synology, wipes all system configurations, clears the administrator password and the encryption key vault, and requires a full DSM reinstall. After one, the STATUS light blinks orange or green (depending on DSM version and whether the model has an ALERT LED), and find.synology.com shows the NAS as Configuration lost.

Do not confuse it with "Not installed". For Not installed, Synology says do not proceed with the installation, or all your data will be deleted.

The five causes Synology lists, and what to do

1. Drives moved from a model pairing Synology does not recommend

Check Synology's migration table. If your original and current models are marked "X", Synology does not recommend moving drives between them. If you still go ahead, double-click the NAS in Synology Assistant and reinstall DSM; Synology says user data on the volumes stays intact.

2. Drives moved from a newer model, or holding a newer DSM version

The drives may include features your NAS does not support, even with the same package architecture. Synology says a reset is required for compatibility, and suggests migrating with Hyper Backup if you want to keep system and package settings.

3. File system errors in the system partition

Synology gives two options:

Synology notes that user configurations in the system partition cannot be backed up if the original drives are damaged.

4. A malfunctioning RESET button

  1. Shut down and clean the device, including around the RESET button.
  2. Power on and see if the status still appears.
  3. If it does, the button may be defective. Synology points to its warranty policy and says that outside North America you should contact the reseller or distributor you bought from.

5. An accidental Mode 2 reset

Follow Synology's reset article for your DSM version (DSM 6.2.4 and above, or 6.2.3 and earlier) and reinstall.

Reinstalling

Once the cause is dealt with, double-click the NAS in Synology Assistant or Web Assistant and follow the wizard. Expect to set up system settings again: Synology describes the reinstall as giving you a fresh system.

When to stop and get help

Stop before reinstalling if you did not press RESET and you do not know why the status appeared, if the drives may be damaged (cause 3), or if Synology Assistant says Not installed rather than Configuration lost. Back up through File Station first wherever Synology's steps allow it.

Questions

Will reinstalling DSM after "Configuration lost" delete my files?

Synology says reinstalling from this status gives a fresh system without affecting volume data, and its connection article says shared-folder data is not deleted. System settings are not kept.

Why does my Synology show Configuration lost when I never pressed RESET?

Synology lists drives moved from another model, file system errors in the system partition (possibly damaged drives) and a malfunctioning RESET button as causes besides an accidental Mode 2 reset.

What is the difference between Configuration lost and Migratable?

Synology says Migratable means the DSM version recorded on the motherboard does not match the version on the drives, often after a drive migration. Configuration lost is usually the result of a Mode 2 reset. Both reinstall DSM without affecting volume data.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-14.