NAS Codex › Synology › Synology drive status "System Partition Failed": degraded vs crashed system partition
Synology drive status "System Partition Failed": degraded vs crashed system partition
Storage Manager shows a drive as System Partition Failed, or the Overview page says the system partition has degraded. Synology separates two cases: degraded, where at least one drive still holds a healthy copy and you can repair it, and crashed, where every copy is gone and DSM has to be reinstalled. Here is how to tell which one you have and what Synology says to do.
Written against: Synology Knowledge Center article tagged DSM 7 series, DSM legacy versions and DSM Enterprise (PAS); the System Partition Failed drive status appears on the HDD/SSD page in DSM 7.2 and above. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Degraded (Overview: "The system partition has degraded. Click the link to repair it."): open Storage Manager > Overview and click Repair, then check HDD/SSD. Any drive still showing System Partition Failed may be defective and should be replaced one at a time. Crashed (Overview: "The system partition has crashed and cannot be repaired."): back up your data first. Synology's fix is a Mode 2 reset and DSM reinstall.
What the system partition is
Synology formats every drive it uses into a system partition, a SWAP partition and a data partition. The system partition holds the operating system, user settings (account credentials, network settings, Control Panel settings) and system logs. On most models DSM mirrors it to every drive with RAID 1, so if one drive fails the system can still start from a healthy one. Your files live in the data partition, not here.
What you see, per Synology
System partition degraded
- On the Storage Manager Overview page: "The system partition has degraded. Click the link to repair it."
- On the HDD/SSD page (DSM 7.2 and above): the drives with issues change to System Partition Failed.
Synology's meaning: the system partition on some drives is inaccessible, but at least one drive is still healthy. Because the partition is mirrored, it degrades instead of crashing. You can keep using the NAS, but Synology recommends repairing it as soon as possible.
System partition crashed
- On the Overview page: "The system partition has crashed and cannot be repaired."
- On the HDD/SSD page: all drives show System Partition Failed, Failed or Critical.
Synology's meaning: the system partition on every drive is inaccessible and cannot be repaired, and you may be unable to reach DSM at all.
Degraded: Synology's repair steps
- Make sure your data is backed up (see the box at the top).
- Launch Storage Manager, go to Overview and click the Repair link. If the link is missing, Synology notes that the Overview page hides it when there are more urgent issues; follow the Overview instructions for those first. Synology's DSM 7 HDD/SSD help gives a second route for a drive in this status: Storage Manager > HDD/SSD, then the Repair System Partition button.
- Wait for the repair to finish.
- Go to HDD/SSD. Any drive still showing System Partition Failed might be defective and need replacing.
- To replace one: deactivate the drive if it is part of a storage pool, replace it, then repair the storage pool or the system partition, whichever the Overview page shows. See the degraded storage pool page for the pool repair.
- If several drives are defective, Synology says to handle them one at a time, finishing each repair before starting the next.
Crashed: Synology's recovery steps
Warning: the next steps include a Mode 2 reset. Synology's reset article says a Mode 2 reset wipes all system configurations, clears the administrator password and the encryption key vault, and needs DSM to be completely reinstalled. Back up before you start.
- Back up your data.
- Use a Mode 2 reset to reset the NAS and reinstall DSM (Synology's reset article for DSM 6.2.4 and above is linked under Sources).
- After installation, launch Storage Manager, go to HDD/SSD and check each drive. Replace any drive not in Healthy status, one at a time.
- Repair the storage pool or the system partition, depending on what the Overview page shows.
On DSM Enterprise (PAS), Synology says the system repairs the system partition automatically and may fail over to the other controller. Its manual steps are to back up, restart the affected controller, and contact Synology Technical Support if the problem remains.
When to stop and get help
Stop if the Overview page says the system partition has crashed and your data is not backed up: do not start a Mode 2 reset until it is. Also stop if more than one drive is Critical or Failing, or the storage pool is also Crashed; see the volume crashed page, where Synology points to data recovery companies when data cannot be read.
Questions
Does repairing the system partition delete my files?
No. The system partition holds DSM, settings and logs; Synology stores your data and packages in the separate data partition. Synology recommends regular backups and puts a backup first in its crashed-partition steps.
Why is there no Repair link on the Overview page?
Synology says the Overview page does not show system partition information or the Repair link when there are more urgent issues. Follow the Overview instructions for those first.
Can I replace several failed drives at once?
Synology says no: handle defective drives one at a time and complete the repair for one drive before moving on to the next.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-14.
- Synology Knowledge Center: The system partition has degraded or crashed. What can I do?
- Synology Knowledge Center: What are drive partitions?
- Synology Knowledge Center: What can I do if a drive is in "Warning," "Critical," or other abnormal statuses?
- Synology Knowledge Center: How do I reset my Synology NAS? (For DSM 6.2.4 or above)
- Synology DSM 7 help: HDD/SSD (opened 2026-11-15)