NAS Codex › QNAP › QNAP disk status shows "Inactive" (or "Disk drive X failed or is unplugged")
QNAP disk status shows "Inactive" (or "Disk drive X failed or is unplugged")
In Storage & Snapshots > Storage > Disks/VJBOD > Disks, one disk shows the status Inactive, and the log may say Disk drive X failed or is unplugged. QNAP's FAQ gives the root cause in one line: "your NAS cannot detect the disk in the drive bay." Here are QNAP's checks, in order.
Written against: QTS and QuTS hero (QNAP FAQ last modified 2025-11-07; QTS 5.1.x documentation). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Inactive means the NAS cannot see the disk at all. QNAP's checks: power off before reseating a disk (unless your model supports hot swapping), make sure the disk is fully and securely inserted, inspect the disk and bay for bent pins or debris, then try the disk in another slot to see whether the disk or the bay is at fault. If the disk itself is faulty, QNAP says to replace it as soon as possible.
What "Inactive" means
QNAP's QTS 5.1 disk status table defines Inactive as "The disk is not connected." The FAQ on the subject explains it as the NAS being unable to detect the disk in the drive bay, and gives these likely causes:
- the disk is not fully seated in the bay;
- a loose connection or a drive bay hardware problem;
- the disk has failed.
An inactive disk cannot be used in storage pools, volumes or as a spare. If it belongs to a RAID group, that group has lost some or all of its redundancy, so check the pool status before anything else.
The log message
Disk drive X failed or is unpluggedQNAP's disk-warning FAQ lists this log entry among the alerts that mean a disk should be replaced if they keep appearing. (The inactive-disk FAQ itself does not quote it.) X is the bay number.
Step 1: Check what the inactive disk was doing
Go to Storage & Snapshots > Storage > Storage/Snapshots and look at the pool status. If the pool now shows Warning (Degraded), the inactive disk was a RAID member and the pool is running without full redundancy. If it shows Warning (Read-Only), QNAP defines that as a RAID group in the pool being Not Active: go to the read-only page and back up before anything else.
Step 2: QNAP's checks
QNAP's warning: "Do not attempt to forcibly remove or insert disks while the NAS is running unless your model supports hot swapping." Its first step: "Power off the NAS if you need to remove or reseat the disk to avoid potential data loss." Check your model's user guide for hot swap support.
- "Check that the disk is properly and securely inserted in the drive bay."
- "If the disk was recently removed, reinsert it and wait for the NAS to detect the disk status."
- "Inspect both the disk and the drive bay for any visible damage or connection issues such as bent pins or debris."
- "If the disk remains inactive, test it in another slot to determine if the problem is with the disk or the NAS."
- If the disk is faulty, QNAP says to "replace it with a new disk as soon as possible."
On step 4: only use an empty slot. Swapping the inactive disk into a bay that holds another pool member is a different operation and can disturb a RAID group that is already short of a disk.
Step 3: Confirm the disk once it reappears
When the disk is detected again, its status should change from Inactive. Select it and click Health to see its S.M.A.R.T. summary. QNAP's health definitions are Good (the disk is normal), Warning (S.M.A.R.T. errors detected; run a full S.M.A.R.T. test and a disk scan) and Error (I/O errors detected; replace the disk immediately). A disk that dropped out and comes back in Warning or Error is not one to rebuild onto.
If it was a RAID member and the rebuild does not start on its own, see rebuild not starting.
When to stop and get help
If the disk stays inactive in every slot and the pool is degraded, back up now while the pool still works. If more disks are inactive than the RAID group can tolerate, do not move or replace disks: QNAP's advice for a RAID group that will not assemble is to contact QNAP support without changing or removing the disks.
Questions
What does Inactive mean for a QNAP disk?
QNAP's disk status table defines Inactive as the disk not being connected. Its FAQ says the NAS cannot detect the disk in the drive bay, usually because it is not seated, the connection or bay is faulty, or the disk has failed.
Can I reseat a QNAP disk while the NAS is running?
Only if your model supports hot swapping. QNAP says to power off the NAS if you need to remove or reseat a disk, to avoid potential data loss.
How do I tell whether the disk or the bay is faulty?
QNAP suggests testing the disk in another slot. If it works there, the original bay is the likely problem; if it stays inactive, the disk is.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-13.