NAS Codex › Synology › Synology Wake on LAN not working: what Synology requires
Synology Wake on LAN not working: what Synology requires
Wake on LAN powers on a Synology NAS that has been shut down. Synology's documentation lists the conditions it needs: the setting enabled, a supported model and port, a proper shutdown with the power still connected, and network equipment that passes the magic packet. This page sets them out, with how to set up and use WOL from Synology Assistant.
Written against: DSM 7 Control Panel and Synology Assistant help, and Synology's WOL model list. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Check four things Synology lists: WOL is enabled in Control Panel > Hardware & Power > General; the NAS was shut down properly (Power button or Shutdown in DSM) and the power cord is still connected; you are not using a 10GbE port or a 10GbE add-in card; and your switches or routers recognize the Magic Packet.
What Wake on LAN needs
- The setting enabled: go to Control Panel > Hardware & Power > General and enable Wake on LAN.
- A proper shutdown: Synology says WOL works only after the NAS is shut down with the physical Power button or Shutdown in DSM, with the power cord left plugged into a working outlet.
- Power never cut: WOL cannot work if power is cut externally, for example if the power cable is unplugged suddenly, there is an area-wide power failure, or a UPS runs out of power after the NAS entered Safe Mode.
- Network gear that passes it: Synology says WOL requires switches or routers that recognize the Magic Packet.
- The IP address and MAC address: a WOL application needs both (or a DDNS hostname instead of the IP).
Models and ports that do not support WOL
- Synology says WOL is supported on most models, with exceptions it lists, including FS3017, SA3400D, SA3200D, DS216se, DS115j, DS214se, RS812, RS212, DS212j, DS112j, DS411slim, DS411j, DS211+, DS211, DS211j, DS410j, DS210j, DS110j and DS508.
- WOL is not supported on 10GbE LAN ports. Embedded 10GbE ports on certain models do not support it, and no 10GbE add-in card does. Your model's datasheet (Download Center > Documents) shows which ports support WOL.
Setting up and using WOL with Synology Assistant
- Enable WOL in Control Panel > Hardware & Power > General.
- In Synology Assistant, open the Management tab, select the NAS and click Set Up WOL to see the MAC address used for WOL. The status changes to WOL.
- To wake it, right-click the NAS and choose WOL > Wake Up. The status shows Progress X%, then WOL when it is on.
Synology Assistant's statuses: -- means WOL is not set up or the NAS does not support it; Off means the NAS is turned off; N/A means WOL is set up but the current status is unknown. Synology also notes the WOL option is not shown if the device does not support it.
When to stop and get help
If the NAS lost power while it was off, WOL will not bring it back; Synology's Power Recovery setting (same page) instead restarts the NAS automatically once power returns after an unexpected power failure. If the NAS starts but you cannot find it, see NAS not found on the local network.
Questions
Why won't my Synology NAS wake on LAN?
Synology says WOL must be enabled in Control Panel > Hardware & Power > General, the NAS must have been shut down properly with power still connected, the port must not be 10GbE, and switches or routers must recognize the Magic Packet.
Does Wake on LAN work on Synology 10GbE ports?
No. Synology says WOL is not supported on 10GbE LAN ports, embedded 10GbE ports on certain models do not support it, and no 10GbE add-in card supports WOL.
Does Synology Wake on LAN work after a power outage?
No. Synology says WOL cannot work if power was cut externally, such as an unplugged cable, an area-wide power failure or a UPS running out after Safe Mode.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.