NAS Codex › Synology › Setting up a UPS so your Synology NAS shuts down safely: what Synology says
Setting up a UPS so your Synology NAS shuts down safely: what Synology says
Synology recommends a UPS because an improper shutdown can cause file system errors. This page sets out what Synology's DSM 7 help says about UPS support: what Standby Mode does, how to set up a USB or SNMP UPS, how to test it, and how one NAS can share a UPS with others. It also covers Synology's method for sizing a UPS.
Written against: Synology DSM 7 help (UPS) and Synology Knowledge Center articles for DSM 7 series and DSM legacy versions. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Plug the UPS's USB cable into the NAS, then go to Control Panel > Hardware & Power > UPS, tick Enable UPS support, choose USB UPS, and set Time before Synology NAS enters Standby Mode to Until low battery or a custom time. In Hardware & Power > General, tick Restart automatically after a power failure so the NAS comes back on. Synology says to test with a simulated power outage before relying on it.
What Standby Mode does
Synology's DSM 7 help says UPS support gives the NAS time to save data and unmount volumes before it loses power and shuts down. In Standby Mode, the NAS stops all services and unmounts volumes, so it can shut down safely when the UPS runs out of power. By default it enters Standby Mode when the UPS starts running low; you can also set a time after a power failure, but if the UPS reaches low battery first, the NAS enters Standby Mode immediately.
If the NAS shuts down during Standby Mode, it turns back on when power returns only if Restart automatically after a power failure is enabled in Control Panel > Hardware & Power > General.
Setting up a USB UPS
- Connect the UPS to a USB port on the NAS.
- On the UPS tab in Control Panel > Hardware & Power, tick Enable UPS support and choose USB UPS as the UPS type.
- Under Time before Synology NAS enters Standby Mode, choose Until low battery, or Customize time and enter seconds, minutes or hours. Synology notes the NAS enters Standby Mode whenever it is low on power, whichever option you pick.
- Optionally tick Shut down UPS when the system enters Standby Mode. Synology says the NAS then shuts down immediately when the power source is lost, so also tick Restart automatically after a power failure. It adds that UPS power-off support varies by brand and model, and some UPS devices cannot be shut down by DSM.
- Click Device Information for details of the UPS, then click Apply.
Test it before you rely on it
Synology says to run a power outage simulation before using the UPS in production: tick Shut down UPS when the system enters Standby Mode, click Apply, and pull the UPS's power cable.
Setting up an SNMP UPS
For a UPS on the network, tick Enable UPS support, choose SNMP UPS, set the Standby Mode timing, and enter the UPS's IP address, SNMP MIB, SNMP version and community string. Synology says DSM supports SNMPv1, SNMPv2c and SNMPv3 UPS devices, and strongly recommends an SNMP UPS for Synology High Availability deployments.
Sharing one UPS between several Synology NAS
Synology explains that only the NAS connected to the UPS (by USB or network) can read its status. That NAS can act as a network UPS server and pass the information to the others:
- On the server NAS: tick Enable network UPS server, click Permitted Synology NAS Devices, enter the IP addresses of the client NAS, and click Apply.
- On each client NAS: tick Enable UPS support, choose Synology UPS server as the type, set the Standby Mode timing (Same as server or a custom time), enter the server's IP address, and click Apply.
Synology says all the NAS must be on the same network, and the switch or hub each one connects through must be plugged into the same UPS; otherwise they cannot pass on UPS information during a power failure.
Choosing a UPS big enough
Synology's article on choosing a UPS says to add up the wattage of every device the UPS will power, then divide by the UPS's output power factor. In its example, a computer (450 W), monitor (20 W), DS918+ (100 W) and network switch (80 W) total 650 W; at a 70% power factor, that needs a UPS with more than 930 W of output power. It also says to check the Synology Products Compatibility List, consult the UPS maker's manual for its real wattage because VA ratings differ between makers, and check the battery capacity and runtime.
When to stop and get help
Synology says some UPS models cannot be shut down by DSM, so run its power outage simulation before relying on the setup. Without Restart automatically after a power failure, a NAS that shut down in Standby Mode will not come back on by itself. If the NAS keeps reporting improper shutdowns, see improper shutdown notifications.
Questions
What is Standby Mode on a Synology NAS with a UPS?
Synology says Standby Mode stops all services and unmounts volumes so the NAS can shut down safely when the UPS runs out of power. By default it starts when the UPS runs low, or after a time you set.
Will my Synology NAS turn back on after a power cut?
Synology says a NAS that shut down during Standby Mode turns on when power returns only if Restart automatically after a power failure is enabled in Control Panel > Hardware & Power > General.
How big a UPS does my Synology NAS need?
Synology says to add up the wattage of all connected devices and divide by the UPS's output power factor; for 650 W at 70%, choose a UPS with more than 930 W output. Check the compatibility list and battery runtime too.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.