NAS Codex › Synology › Synology NAS unresponsive, frozen or restarting on its own: what Synology says to check

Synology NAS unresponsive, frozen or restarting on its own: what Synology says to check

Your Synology NAS stops responding: you cannot sign in to DSM, the DSM page freezes, the system will not restart, or services drop out. Or it shuts down and restarts on its own. Synology's Knowledge Center covers this in an article on unresponsive NAS, an article on when and how to run a memory test, and an article on improper shutdown notifications. This page sets them out in order.

Written against: Synology Knowledge Center articles for DSM 7 series and DSM legacy versions. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

First rule out the network: try another Cat 5e or newer cable, and another port on the router and on the NAS. Then press and hold the power button for at least 3 seconds. If it beeps and shuts down, it is responsive; if it does not shut down, Synology says you may have to unplug the power cord. After rebooting, run a memory test in Synology Assistant three times, then check in Storage Manager that no storage pool is degraded or busy and that volume usage is under 90%.

Step 1: rule out the network

Synology's article on an unresponsive NAS starts by checking whether the NAS can be reached on the local network. If not, check the Ethernet cable and port:

Step 2: is the NAS actually unresponsive?

Press and hold the power button for at least three seconds, or until you hear a beep. Synology describes three outcomes:

If it does not shut down after you hold the power button, Synology says you may have to unplug the power cord. Holding the power button for 10 seconds forces the NAS to shut down. After plugging it back in and rebooting, run a memory test, then check the NAS's status (Steps 3 and 4). If the NAS will not boot at all, Synology points to its separate article on a power LED that keeps blinking.

Step 3: run a memory test three times

Synology's memory test article lists unexpected shutdowns or reboots that are not caused by the power supply as one reason to run the test, along with the DSM install or update errors ERR_PATCH_FILE (13) and ERR_EXTRACT (26). It recommends running the test three times:

  1. Install Synology Assistant from the Download Center, launch it, click the icon at the upper right, tick Memory Test and click OK.
  2. Select the NAS, make sure its status is Ready, click Memory Test and follow the wizard.
  3. The NAS reboots during the test, and its status shows "Performing memory test (x%)". Do not close Synology Assistant.

If the test passes, the status returns to Ready. If it fails, the message "One or more errors have been found by the memory diagnostic test" appears, which Synology says means the memory may be defective; it strongly recommends returning the NAS for repair if it is under warranty. Synology notes the status still shows Ready even after a failed test, so read the message. Allow 1 to 1.5 hours per test for 16 GB of memory or less, and 1.5 to 3 hours for 32 GB or more; keep at least one built-in LAN port connected, and expect the NAS to be unavailable during the test.

Both articles say not to use non-Synology memory modules or devices that are not on the Synology Products Compatibility List.

Step 4: check storage after the reboot

In DSM 7, open Storage Manager > Storage and check:

If it shuts down and restarts by itself

Synology's improper shutdown article lists common causes: a power outage, power cords not connected properly, a power supply malfunction, a memory module abnormality, or non-original memory modules. First rule out external power: check the plugs, check whether other devices on the same multi-outlet had power problems, and check whether someone forced a shutdown by holding the power button.

Then, in Control Panel > Hardware & Power > General, untick Restart automatically when power supply issue is fixed. Synology says that if the NAS does not start up again after an improper shutdown, the cause is probably a power supply malfunction; if it still starts up again, run a memory test three times. Power supply and memory faults can be covered by warranty service.

When to stop and get help

An improper shutdown can cause file system errors, so Synology highly recommends backing up your data to another server or cloud storage as soon as possible, for example with Hyper Backup, and recommends a UPS against power problems. Pull the power cord only if the power button does not shut the NAS down. If the NAS keeps logging improper shutdowns, see improper shutdown notifications.

Questions

What do I do if my Synology NAS is frozen?

Synology says to check the cable and ports, then hold the power button for at least three seconds. If it does not shut down, you may have to unplug the power cord. After rebooting, run a memory test and check the storage pools and volume usage.

How do I run a memory test on a Synology NAS?

Synology says to use Synology Assistant: tick Memory Test in its settings, select the NAS while it shows Ready, click Memory Test and follow the wizard. Run it three times; the NAS reboots during the test.

Why does my Synology NAS restart by itself?

Synology lists power outages, loose power cords, power supply malfunction, memory module abnormalities and non-original memory as common causes of improper shutdowns, and says to run a memory test three times if power is ruled out.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.