NAS Codex › Synology › Synology keeps sending "Improper shutdown" notifications: how Synology says to find the cause
Synology keeps sending "Improper shutdown" notifications: how Synology says to find the cause
Your Synology NAS keeps sending "Improper shutdown" notifications. Synology's article on this lists the usual causes, from a power outage to faulty or non-original memory, and gives a short order of checks that separates an outside power problem from a fault inside the NAS. This page follows that order and adds Synology's steps for the memory test it asks for.
Written against: Synology Knowledge Center articles for DSM 7 series, DSM legacy versions and DSM Enterprise, and DSM 7 help (Hardware & Power > General). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
First rule out outside power: check the plugs, check whether other devices on the same multi-outlet had power problems, and check whether someone forced the NAS off with a long press of the power button. If none of those explains it, go to Control Panel > Hardware & Power > General and untick Restart automatically when power supply issue is fixed. If the NAS then stays off after an improper shutdown, Synology says the power supply is the likely cause. If it still starts up again by itself, run Synology's memory test three times.
What usually causes it
Synology says an improper shutdown is often caused by:
- a power outage;
- power cords not connected properly;
- a malfunction of the storage system's power supply;
- an abnormality of the memory modules;
- non-original memory modules.
Step 1: rule out outside power
Synology's first checks:
- Make sure the power plugs are properly connected to the outlet.
- If the NAS is plugged into a multi-outlet, check whether other devices on the same multi-outlet have had power problems.
- Check whether the system was forced to shut down by long-pressing the power button.
Step 2: power supply or memory? (DSM)
If outside power is not the cause, Synology's next step is in DSM:
- Go to Control Panel > Hardware & Power > General and make sure Restart automatically when power supply issue is fixed is not selected.
- If the system does not start up again after an improper shutdown, Synology says it is probably a power supply malfunction.
- If the system still starts up again after an improper shutdown, run a memory test three times.
The DSM 7 help for this settings page describes Power Recovery. If the system shuts down because of an unexpected power failure, it automatically forces a reboot once power is restored.
Synology says that if the cause is a power supply malfunction or a memory module abnormality, you can request warranty service.
Running Synology's memory test
Synology recommends the memory test when the NAS shuts down or reboots unexpectedly for a reason unrelated to the power supply, and also for the DSM install or update errors ERR_PATCH_FILE (13) and ERR_EXTRACT (26). It recommends running it three times.
- Download and install Synology Assistant from Synology's Download Center.
- Launch it, click the upper-right icon, tick Memory Test and click OK.
- Select the NAS. Its status must be Ready. Click Memory Test and follow the wizard.
The NAS reboots during the test. Do not close Synology Assistant while it runs. The status shows Performing memory test (x%).
- Pass: the status returns to Ready, and you can run the test again.
- Fail: the message
One or more errors have been found by the memory diagnostic testappears. Synology says the memory may be defective and strongly recommends returning the NAS for repair if it is under warranty. Synology notes that the status still shows Ready even after a failed test, so read the message, not the status.
Synology's notes on the test:
- At least one built-in LAN port must be connected to an available network.
- Allow 1.5 to 3 hours per test on models with 32 GB or more of memory, and 1 to 1.5 hours with 16 GB or less. The NAS is unavailable while it runs.
- Synology does not recommend replacing onboard memory on models that do not support memory expansion. On models that do, it points to the Synology Products Compatibility List.
When to stop and get help
Synology warns that an improper shutdown can cause file system errors or stop the system running properly, and highly recommends backing up your data to another server or cloud storage as soon as possible, for example with Hyper Backup. Back up before running the memory test, which reboots the NAS. Synology also recommends a UPS to protect against data loss or file system errors from power problems. If the NAS will not start at all, see Power LED blinking, won't boot.
Questions
Why does my Synology keep saying Improper shutdown?
Synology lists power outages, badly connected power cords, a faulty power supply, abnormal memory modules and non-original memory modules as the usual causes. Its checks start by ruling out outside power, then test the power supply and the memory.
Why untick Restart automatically when power supply issue is fixed?
With that setting off, Synology says a NAS that does not start again after an improper shutdown probably has a power supply fault, while one that still restarts by itself should get a memory test, run three times.
Does a failed Synology memory test change the status?
No. Synology says the status still shows Ready even when the test fails. A failure shows the message One or more errors have been found by the memory diagnostic test, and Synology recommends returning the NAS for repair if it is under warranty.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.