NAS Codex › Synology › DSM update not showing up or failing to download: what Synology says
DSM update not showing up or failing to download: what Synology says
A new DSM version is listed in Synology's Download Center but not in your NAS's Control Panel, or the update fails with "Connection failed" or will not download. Synology's Knowledge Center explains why an update may not be offered to your NAS, how to fix connection failures, and how to install DSM manually. This page sets out all three.
Written against: Synology Knowledge Center articles for DSM 7 series and DSM legacy versions, and DSM 7 help (Update). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
If the update is not offered, it may still be in Synology's staged rollout, or Smart Update may have decided your NAS does not need it; you can install it manually from the Download Center with Manual DSM Update. If you see "Connection failed", set DNS to 8.8.8.8 or 1.1.1.1, turn off the proxy, set IPv6 to Off, turn the firewall off temporarily, and sync the time with an NTP server. If a download fails, Synology says to check the NAS's internet connection, or try later if the server is busy.
Why the update is not offered
Synology says your NAS decides which versions to show based on Synology's rollout policy and your system configuration. Its article lists these reasons:
- Staged Rollout. Updates are released in stages: devices are randomly assigned to groups, and the update reaches each group gradually, so some users see a new version before others. Synology says updates usually reach all regions within a few weeks of the first release. To get it straight away, download and install the update from the Download Center.
- Smart Update. If an update's changes are not relevant to your NAS, Synology does not notify you. Smart Update decides based on the services running on your system. If no update appears in Control Panel > Update & Restore, it may have been skipped by Smart Update. Synology notes Smart Update cannot be turned off.
- Not detected yet. The update may be available but the NAS has not checked. Set how often it checks in Control Panel > Update & Restore > Update Settings.
- Not a general release. Preview, Beta and Release Candidate versions are never offered as notifications. Release Candidates are only in the Download Center and are removed once the official version is out.
- Not pushed to your system. Some specific systems do not get the notification; Synology says to check the DSM release notes, and that you can update manually.
Synology adds that all updates are cumulative and include the fixes in earlier updates, and that a later change to your configuration can make an update notification appear.
"Connection failed"
Synology's article on the "Connection failed" message gives these checks for errors in DSM:
- Connect a computer to the same local network as the NAS, with its Wi-Fi turned off. If the computer cannot reach the internet, check your network first (gateway, DNS server and proxy server settings).
- In Control Panel > Network > General, tick Manually configure DNS server and set it to 8.8.8.8 or 1.1.1.1 (in China, Synology says 114.114.114.114 or 223.5.5.5).
- In Control Panel > Network > General > Proxy, turn off Connect via a proxy server. If that fixes it, check that your proxy allows the websites Synology lists.
- In Control Panel > Network > Network Interface, edit the interface: set IPv6 setup to Off, and on the IPv4 tab select DHCP and turn off the MTU setting.
- In Control Panel > Security > Firewall, turn the firewall off temporarily. To turn it back on, add the IP addresses Synology lists to the firewall rules so the NAS can reach those sites on ports 80 and 443. Also check that the firewall profile does not set the Synology update sites to Deny.
- In Control Panel > Regional Options > Time, use Synchronize with NTP server and click Update Now.
Synology notes that if turning IPv6 off fixes the problem, the cause may be IPv6 routing: make sure the NAS can reach Synology's servers over your IPv6 routing.
Installing DSM manually
Synology's DSM 7 help gives the manual route:
- In the Synology Download Center, select your product type and model.
- Under the Operating System tab, download the DSM update file.
- In DSM, click Manual DSM Update, click Browse to select the file, and continue with the installation. The system restarts automatically when the update is complete.
The help also says that if an update download fails, you should check the NAS's internet connection, and if the download server is busy, try again later. It notes you can only update to a newer version, updates are irreversible, and updating does not affect your data, but Synology strongly recommends a backup before you start.
When to stop and get help
DSM updates cannot be undone: Synology says you can only update to a newer version, so back up first as it recommends. The IPv6 and firewall changes are tests: turn them back on afterwards, adding the firewall allow rules Synology describes. If the update stops with a capacity error instead, see insufficient system capacity for updates.
Questions
Why is the new DSM version not showing on my Synology?
Synology says updates go out in a staged rollout over a few weeks, and Smart Update skips updates your system does not need. You can install the update manually from the Download Center with Manual DSM Update.
How do I fix 'Connection failed' when updating DSM?
Synology says to set DNS to 8.8.8.8 or 1.1.1.1, turn off the proxy, set IPv6 to Off with DHCP and no MTU setting, temporarily turn off the firewall, and sync the time with an NTP server.
Can I roll back a DSM update?
No. Synology says you can only update to a newer version and updates are irreversible. Updating does not affect data, but Synology strongly recommends backing up first.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.