NAS Codex › Synology › Can't connect to your Synology NAS via QuickConnect: what Synology says to check
Can't connect to your Synology NAS via QuickConnect: what Synology says to check
You can reach your Synology NAS on the local network by its IP address, but not over the internet through QuickConnect. Synology's Knowledge Center has a checklist for exactly this, plus DSM 7 help on QuickConnect's options and an article for DDNS, the other way in. This page puts them together, starting with the checks that rule out Synology's side.
Written against: Synology Knowledge Center articles for DSM 7 series and DSM legacy versions, and DSM 7 help (QuickConnect). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
First check Synology Service Status shows QuickConnect as Operational, and sign in to your Synology Account to see that QuickConnect's status is normal. Then in DSM 7, confirm Control Panel > External Access > QuickConnect > Enable QuickConnect is ticked and the services you need are enabled under Advanced Settings. If it still fails, Synology's steps are: get the IP by DHCP, set DNS to 8.8.8.8 or 8.8.4.4, turn IPv6 off and the firewall off temporarily, untick the manual MTU value, and sync the time with an NTP server.
Preliminary checks
Synology's QuickConnect troubleshooting article starts with checks outside your NAS settings:
- Go to Synology Service Status and check whether QuickConnect shows Operational. If not, Synology says the service is undergoing maintenance, and you should wait until it resumes normal operations.
- Make sure the NAS is properly connected to the internet. Synology suggests connecting another device, such as a computer, to the same network ports and cables to test the connection.
- Sign in to your Synology Account and check that QuickConnect's status is normal. For a NAS located in China, the QuickConnect ID must be registered with an authenticated China phone number under the Synology Account; if the status is Failed, click Update to register the number.
Troubleshooting steps on the NAS
- Check QuickConnect is enabled. In DSM 7, go to Control Panel > External Access > QuickConnect, make sure Enable QuickConnect is ticked, then click Advanced Settings and confirm the services you want to reach through QuickConnect are enabled.
- Get the IP address by DHCP. Go to Control Panel > Network > Network Interface > LAN > Edit > IPv4 and select Get network configuration automatically (DHCP).
- Set the DNS server. In Control Panel > Network > General, tick Manually configure DNS server and set it to 8.8.8.8 or 8.8.4.4 (in China, Synology says to use 114.114.114.114 or 223.5.5.5).
- Temporarily turn off IPv6. In Network Interface > LAN > Edit > IPv6, set IPv6 setup to Off.
- Temporarily disable the firewall. In Control Panel > Security > Firewall, untick Enable firewall.
- Disable the MTU value setting. In Network Interface, double-click the LAN and, under IPv4, make sure Set MTU value manually is unticked. Synology notes some models do not support changing the MTU; skip this step if the checkbox is not shown.
- Sync the time with an NTP server. In Control Panel > Regional Options > Time > Time Setting, choose another NTP server and click Update Now.
- If your internet provider uses DS-Lite, restart the router or modem it provided.
Synology adds that if setting DHCP fixes the problem, the cause may be the parent router's settings. To use a manual configuration and keep QuickConnect working, allow the NAS to connect to the internet in the parent router's settings. Synology also recommends installing the latest DSM version.
QuickConnect options in DSM 7
Synology's DSM 7 help explains that QuickConnect lets client applications reach the NAS over the internet without setting up port forwarding rules. Two settings under Control Panel > External Access > QuickConnect > Advanced > Advanced Settings are relevant:
- Enable QuickConnect relay service: relays the connection through a Synology Relay Server when direct QuickConnect access is not possible in the current network environment. Synology notes a relayed connection may be slow because of longer network latency.
- Applications/Services: where you enable or disable QuickConnect for each application or service.
The help also says that for better QuickConnect performance you can configure port forwarding in Control Panel > External Access > Router Configuration, for example DSM on 5000 (HTTP) and 5001 (HTTPS), and Synology Drive on 6690. A QuickConnect ID can only contain English letters, numbers and dashes, must start with a letter, and cannot end with a dash.
If you use DDNS instead
Synology's DDNS article repeats the DNS, IPv6 and NTP checks above, and adds: make sure the DDNS status is Normal in Control Panel > External Access > DDNS, that the hostname resolves to your external IP address, that port forwarding is set up on the parent router or modem, and that firewall rules on the router and NAS allow the forwarded ports. It notes that some internet providers, such as cellular and community networks, do not support port forwarding in some circumstances; in that case Synology suggests using QuickConnect instead. If DDNS fails only from inside your own network, Synology says the parent router must support NAT loopback.
When to stop and get help
The IPv6 and firewall changes are tests, not fixes: Synology says to turn them off temporarily, so turn them back on once you know the cause. Synology also says to install the latest DSM version to protect your data from security issues. If you cannot reach the NAS even on the local network, see NAS not found on the local network.
Questions
Why is Synology QuickConnect not working?
Synology says to first check Synology Service Status shows QuickConnect as Operational and your Synology Account shows QuickConnect as normal. Then check QuickConnect is enabled, use DHCP, set DNS to 8.8.8.8, and temporarily turn off IPv6 and the firewall.
What does the QuickConnect relay service do?
Synology says it relays your QuickConnect connection through a Synology Relay Server when direct access to the NAS is not possible in the current network. A relayed connection may be slow because of longer latency.
QuickConnect or DDNS: which should I use?
Synology says QuickConnect works without port forwarding rules. DDNS needs port forwarding on your router, and some providers such as cellular and community networks do not support it; Synology suggests QuickConnect in that case.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.