NAS Codex › Synology › Forgot your Synology DSM administrator password: what Synology says to do
Forgot your Synology DSM administrator password: what Synology says to do
You cannot sign in to DSM because the administrator password is forgotten, or because you have lost the phone or security key for 2-factor authentication. Synology's Knowledge Center covers both with the RESET button on the NAS (a Mode 1 reset). This page sets out the steps, exactly what a Mode 1 reset changes, how it differs from the Mode 2 reset that re-installs DSM, and what Synology says to check if the password does not reset.
Written against: Synology Knowledge Center articles for DSM 7 series, DSM legacy versions and DSM Enterprise (PAS). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Press and hold the RESET button with a paper clip for about 4 seconds, until you hear a beep, then release it immediately. Open finds.synology.com (or Synology Assistant), double-click the NAS, sign in as admin with the password field blank, set a new password and click Submit. Synology says this does not affect stored data, but it resets the network settings to DHCP, so the NAS's IP address may change. If you only need to change a password you still know, use DSM > Personal > Account instead.
Before you press anything
Synology's reset article for DSM 6.2.4 and above makes these points first:
- Resetting the NAS does not affect stored data, but Synology strongly advises backing up data and system configurations with Hyper Backup first.
- The reset needs at least one installed drive and DSM set up.
- If you only need to change an administrator password, you may not need a reset: go to DSM > Personal > Account.
- The NAS should show the status Ready in Web Assistant (finds.synology.com) or Synology Assistant.
Synology also lists two options in Control Panel > Update & Restore > System Reset, both disabled by default: Keep admin password unchanged, and on DSM 7.3 and above, Automatically lock encrypted storage entities. If the first one was turned on earlier, a Mode 1 reset will not reset the password (see the last section).
Mode 1 reset: step by step
- Locate the RESET button. Synology says to check your device's Hardware Installation Guide or Product Manual if you need help finding it.
- With a paper clip, press and hold it for about 4 seconds until you hear a beep, then release it immediately.
- Open finds.synology.com in a browser (Web Assistant) or use the Synology Assistant desktop utility, and double-click your NAS.
- On the sign-in page, enter the default username
admin, leave the password field blank, and click Sign In. - Reset the password and click Submit. If there is only one administrator account,
adminis filled in for you; if there are several, choose the account from the drop-down menu. - Click Sign In Now and sign in with the new password.
On DSM 6.2.3 and earlier, Synology's steps differ: create a strong password, sign in as admin, reset the password of the administrator account you want to use in Control Panel > User, then disable the admin account.
What a Mode 1 reset changes
For DSM 6.2.4 and above, Synology lists these effects:
- The admin account is restored to default, and its 2-factor authentication is disabled.
- The DSM management port is reset to 5000 or 5001.
- Network settings are reset to DHCP (on DSM 7.2 and above, the IPv4 address, DNS, gateway and other interfaces; on 6.2.4 to 7.1.x, IPv4 and IPv6). PPPoE is disabled. Synology notes the LAN IP address may change.
- Auto Block and firewall rules are disabled.
- Encrypted storage: on DSM 7.3 and later the system unlocks encrypted volumes and shared folders by default, unless you enabled the lock option. On DSM 7.2 and earlier, encrypted folders are locked and Mount automatically on startup is disabled, a machine-key cipher is deleted from Key Manager, and encrypted volumes are locked because the Encryption Key Vault is erased; you re-enable the vault and use each volume's recovery key.
- A high-availability cluster and a Virtual Machine Manager cluster are removed.
Synology adds that when you reset the password of an administrator account other than admin, the admin account is deactivated for security reasons.
Lost the phone for 2-factor authentication
Synology has a separate article for when you can no longer complete the second sign-in step, for example after losing your phone or hardware security key with no backup email set up. If the NAS has other administrators, ask one to go to Control Panel > User & Group, select your account, click Edit, and on the Info tab click Disable 2-factor Authentication. If you are the only administrator, use the Mode 1 reset above. Synology also says to keep the NAS syncing with an NTP server and the system time correct, in Control Panel > Regional Options > Time, so 2-factor authentication works normally afterwards.
Mode 2 is a different reset
Mode 2 re-installs DSM. Synology's steps are to hold RESET for about 4 seconds until the beep, release, and within 10 seconds hold it again for 4 seconds until 3 more beeps. After about 2 minutes the STATUS light blinks orange or green and the NAS shows Configuration lost. Synology says Mode 2 wipes all system configurations, clears the administrator password and the encryption key vault, and requires a full DSM re-installation; data in shared folders remains.
If the password did not reset
Synology gives two possible reasons:
- Your browser saved the old password. Try another browser, or an InPrivate (Edge), Incognito (Chrome) or Private (Firefox, Safari) window.
- Keep admin password unchanged was selected in Control Panel > Update & Restore > System Reset. Then you need the Mode 2 reset and DSM re-installation.
Synology also notes that if the NAS does not beep when you hold RESET, this may be a hardware failure, and to contact your reseller for RMA service if it is under warranty. If you still cannot reset the password, contact Synology Technical Support.
When to stop and get help
Release RESET at the first beep. A second press within 10 seconds starts Mode 2, which Synology says wipes all system configurations and requires re-installing DSM. If the NAS does not appear in Web Assistant after the reset, its IP address may have changed; see NAS not found on the local network.
Questions
How do I reset a forgotten Synology admin password?
Synology says to hold the RESET button for about 4 seconds until a beep (Mode 1), then open finds.synology.com, sign in as admin with a blank password, set a new password and click Submit.
Does a Mode 1 reset delete data on my Synology NAS?
Synology says resetting does not affect stored data. Mode 1 resets the admin account, network settings, management port, Auto Block and firewall rules. Synology still advises a Hyper Backup backup first.
I lost my phone for DSM 2-factor authentication. What now?
Synology says another administrator can disable your 2-factor authentication in Control Panel > User & Group. If you are the only administrator, a Mode 1 reset disables 2-factor authentication for the admin account.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.
- Synology Knowledge Center: How do I sign in if I forgot the password for the administrator account on my Synology storage system?
- Synology Knowledge Center: How do I reset my Synology NAS? (For DSM 6.2.4 or above)
- Synology Knowledge Center: I can't sign in to Synology storage system using 2-factor authentication (2FA). What can I do?