NAS Codex › Synology › Synology NAS won't hibernate or keeps waking up: what Synology says stops it

Synology NAS won't hibernate or keeps waking up: what Synology says stops it

Drive Hibernation is set, but your Synology NAS never goes to sleep, or wakes up again soon after. Synology's article on this lists the volume states, DSM services and packages that can stop hibernation or cause unintended wake-ups, and gives two other ways to save power if you do not want to turn those off. This page sets out that list with the DSM 7 paths Synology gives, plus what Synology says each hibernation mode does.

Written against: Synology Knowledge Center articles for DSM 7 series and DSM legacy versions, and DSM 7 help (Power Schedule). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

Check the volume first: a degraded or crashed volume, or no volume at all, stops hibernation. Then go through Synology's list of services that wake the NAS, such as scheduled DSM update checks, data scrubbing and S.M.A.R.T. test schedules, Security Advisor scans, QuickConnect, DDNS, NTP, SMB activity from computers on the network, thumbnail indexing and attached USB devices, and the packages that keep it busy, such as Synology Drive Server with connected devices, Surveillance Station, Plex and Container Manager. If you want to keep those running, Synology suggests a Power Schedule or auto poweroff instead.

Where hibernation is set, and the modes

Synology says hibernation is set at Control Panel > Hardware & Power > Drive Hibernation on DSM 7.3 and above, and at Control Panel > Hardware & Power > HDD Hibernation on DSM 7.2 and earlier. Its modes:

Synology says drives first power down after the idle time you set, and Advanced Hibernation or Deep Sleep then cuts power use further. Mode availability varies by model, so check your model's Product Manual.

Volume status

Synology says the NAS may not hibernate if a volume is degraded or crashed, or if no volume has been created.

DSM services that stop hibernation or wake the NAS

Packages that stop hibernation

Synology lists these packages or package settings, among others:

Synology also says any running third-party package, and any attached USB device, may stop hibernation.

If you want to keep those running: two other ways to save power

When to stop and get help

Some items on Synology's list are maintenance tasks that wake the NAS on a schedule: data scrubbing, S.M.A.R.T. and IronWolf Health tests, and Security Advisor scans. Synology's article gives where each schedule is set, so you can see when they run before changing anything. If the volume is degraded or crashed, deal with that first: see storage pool degraded or volume crashed.

Questions

Why won't my Synology NAS hibernate?

Synology lists a degraded or crashed volume, scheduled tasks such as DSM update checks, data scrubbing and S.M.A.R.T. tests, network services such as QuickConnect, DDNS and NTP, SMB activity on the network, indexing, attached USB devices, and packages such as Synology Drive Server, Surveillance Station and Plex.

Where is HDD Hibernation in DSM 7?

Synology says it is at Control Panel > Hardware & Power > Drive Hibernation on DSM 7.3 and above, and at Control Panel > Hardware & Power > HDD Hibernation on DSM 7.2 and earlier.

How can I save power if my Synology NAS won't hibernate?

Synology suggests a Power Schedule to start up and shut down at set times, or Enable auto poweroff under Drive Hibernation, with Wake-on-LAN enabled at Control Panel > Hardware & Power > General > Power Recovery so you can wake it remotely.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.