NAS Codex › Synology › Synology NAS making unusual noises: how Synology says to find the source and quiet it
Synology NAS making unusual noises: how Synology says to find the source and quiet it
Your Synology NAS is louder than it should be, or makes a noise it did not make before. Synology's article on unusual noises says some noise is normal in operation, lists the usual sources, and gives a simple test that separates noise from the drives from noise from the fan or the unit itself. This page follows that test and adds what DSM help says about Fan Speed Mode and Power Schedule, the two settings Synology points to.
Written against: Synology Knowledge Center articles for DSM 7 series and DSM legacy versions, and DSM 7 help (Hardware & Power > General and Power Schedule). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Shut the NAS down, take out all drives and drive trays, and power it on with no trays installed. If the noise stops, it came from the drives or the trays vibrating: Synology suggests fastening the drives with screws instead of the fastening panels, or trying a different drive. If the noise is still there, it is the fan or the unit itself: clean the dust inside and on the fan and check the fan screws. If the fan is simply too loud, set Fan Speed Mode to Quiet Mode in Control Panel > Hardware & Power > General.
What can make noise
Synology says a Synology NAS in operation may make some noise. The possible sources it lists are:
- the drives;
- the fan;
- vibration of the drives and drive trays;
- other causes.
Step 1: run Synology's no-drives test
- Shut down your Synology NAS.
- Remove all drives and drive trays.
- Power on the device again without any drive trays installed, and listen for whether the unusual noise is still there.
If the noise stopped: drives or trays
Synology gives two possibilities:
- The noise may be vibration of the drives and drive trays. Synology suggests replacing the fastening panels with screws to reduce it.
- The noise may come from the drives you use. Synology says you can use a different drive to fix it.
If the noise is still there: the fan or the unit
Synology says the noise may then come from the fan or the device itself. Its steps:
- Clean the dust inside the device and on the fan.
- Check that the fan screws are fastened.
If the fan is too loud: change Fan Speed Mode
Synology's first step for a noisy fan is Quiet Mode, at Control Panel > Hardware & Power > General > Fan Speed Mode. DSM 7 help describes the modes:
- Full-Speed Mode: cools the NAS quickly with the highest fan speed, but makes more noise.
- Cool Mode: balances cooling and noise with a higher fan speed.
- Quiet Mode: runs the fans at a lower speed with less noise, but may raise the temperature.
- Low-Power Mode: runs at a lower speed to cut noise and power use, but may raise the temperature. When the NAS is cool, the fan stops to save power. Only specific models have this mode.
Synology's notes on these options:
- Fan speed modes are only available on Synology NAS models with system fans.
- The options vary with the hardware and configuration. Installing additional network interface cards disables some fan speed options to keep heat dissipation optimal.
- Fan Speed Mode controls the NAS's own fans. If the NAS has a PSU (power supply unit), the PSU's fans are controlled by the PSU.
If Quiet Mode does not help
- Out of warranty: Synology says you can look up the fan model for your device and buy a replacement fan.
- Within warranty and the fan malfunctions, or if you still cannot find the cause, Synology says to contact the reseller you bought the NAS from for RMA service.
If the idle noise still bothers you: Power Schedule
Synology suggests scheduled shutdowns and startups so the NAS runs only when you are not sleeping. DSM 7 help sets this up at Control Panel > Hardware & Power > Power Schedule:
- Click Create, choose Startup or Shutdown, and set the date and time.
- Click OK, then Apply. Summary shows the weekly schedule. You can set up to 100 schedules.
DSM help says a scheduled shutdown may not happen while Storage Manager is creating or removing storage pools or volumes, running Secure Erase or updating drive firmware, while shared folders are being encrypted, while DSM is updating, while Package Center is running tasks, while databases are updating, or while data backup tasks run. It also says power schedules are not applied after a temporary power interruption, and recommends an SNMP or USB UPS. Only some package architectures still run the startup schedule after a temporary power interruption: Denverton, Grantley, Broadwell (including Broadwellnk, Broadwellntb and Broadwellntbap), Bromolow, Apollolake and Purley.
When to stop and get help
Shut the NAS down properly before taking the drives out for the test. If DSM also shows a drive warning, see drive status Warning, Critical or Failing. If the sound is a beep rather than a mechanical noise, see NAS keeps beeping.
Questions
Why is my Synology NAS making a strange noise?
Synology lists the drives, the fan, vibration of the drives and drive trays, and other causes. Its test is to shut down, remove all drives and trays, and power on: if the noise stops it came from the drives or trays, and if not it came from the fan or the unit.
How do I make my Synology fan quieter?
Synology's first step is Quiet Mode at Control Panel > Hardware & Power > General > Fan Speed Mode. DSM help says Quiet Mode lowers the fan speed and noise but may raise the temperature, and the options depend on the model and configuration.
What if the Synology fan is still loud?
Clean the dust and check the fan screws. Synology says that out of warranty you can buy a replacement fan for your model, and within warranty, or if you cannot find the cause, you should contact your reseller for RMA service.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.