NAS Codex › Synology › Synology drive re-identification count increasing, or drive reconnection alerts
Synology drive re-identification count increasing, or drive reconnection alerts
Storage Manager keeps a few health counters for each drive. When the Drive re-identification count rises, or DSM sends alerts about drive reconnection, I/O command timeouts or drive access errors, Synology says the cause can be either the drive or the drive slot it sits in. Its fix is the same in both cases: watch the count, then swap drives to see whether the problem follows the drive or stays with the slot.
Written against: DSM 6.2 to DSM 7.2.1 (Synology KB articles: drive re-identification count, drive or drive slot errors, identifying drives). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Open Storage Manager > HDD/SSD, select the drive, click Health Info and go to History > Key Information of Drives. If the Drive re-identification count graph is stable, Synology says to keep monitoring: removing and reinserting a drive can cause a small increase. If it keeps climbing, do the swap test below.
Symptoms Synology describes
- The Drive re-identification count shows a value other than 0. To see it, go to Storage Manager > HDD/SSD, select the drive, click Health Info and check the Statistics section.
- You receive a Drive re-identification (IDNF error) alert by email or in DSM desktop notifications.
- Related signs: a drive status of Drive slot disabled or Cannot be detected by controller; frequent logs of I/O errors, or of a drive being plugged in or out when nobody touched it; alerts about I/O command timeouts, drive reconnection or drive access errors.
Synology's diagnosis for these errors is an unstable connection between the drive and the system, which can come from the drive itself or from the drive slot.
Find the drive error logs
- DSM 7.2 or above: go to Log Center > Logs and select Drives as the log type.
- DSM 7.1 or below: go to Storage Manager > HDD/SSD > Logs.
Step 1: watch the count
- Go to Storage Manager > HDD/SSD and select the suspected drive.
- Click Health Info, then go to History > Key Information of Drives.
- Check the Drive re-identification count graph.
Stable: keep monitoring the drive. Increasing: continue with the swap test.
Step 2: swap drives to find the cause (multi-bay models)
- Make sure all storage pools are in Healthy status. If one isn't, follow the Suggestion shown under the storage pool first.
- Power off the NAS.
- Move the suspected drive into a working empty drive slot. If there is no empty slot, swap it with another healthy drive in the same NAS.
- Power on the NAS and go to Storage Manager > HDD/SSD.
- Check the graph (or the errors) for both the suspected drive and the healthy drive now in the suspected slot.
- The problem follows the drive: Synology says the drive is likely at fault and recommends replacing it to avoid possible data loss.
- The problem stays with the slot: the healthy drive now shows the errors, so the drive slot is likely faulty. Synology recommends backing up all your data and replacing the Synology NAS.
Synology numbers the drives of models with two or more bays from left to right or top to bottom. Check the "Install Drives" section of your model's Product Manual to find the right one.
One-bay models
- Back up all your data and power off the NAS.
- Replace the drive with a healthy compatible drive and power on.
- Install DSM, create a new storage pool and volume, and restore your backup.
- Watch the new drive's Drive re-identification count. If it increases, the slot may be the problem and Synology recommends backing up and replacing the NAS. If it stays stable, the problem was the drive you replaced.
Drives in an expansion unit
Synology says to make sure the expansion unit is compatible with your model and that the expansion cable is securely connected. Run the same swap test inside the expansion unit. If the healthy drive in the suspected slot starts showing the increase, the cause may be the drive slot or the expansion unit cable; Synology recommends replacing the cable and continuing to monitor the count.
Replace the defective drive
Check the Synology Products Compatibility List to make sure the replacement drive is compatible with your model. Then:
- RAID type with data protection: remove and replace the drive, then repair the storage pool.
- RAID type without data protection: back up all your data, power off, replace the drive, power on, create a new storage pool and volume (install DSM first on a one-bay model), and restore the backup.
On DSM 7.2.1 or above, Synology says to check the drive status shown in Storage Manager > HDD/SSD to decide whether a drive needs replacement.
When to stop and get help
If the swap test shows the problem staying with the drive slot, Synology recommends backing up all your data and replacing the Synology NAS.
Questions
What does drive re-identification count mean on Synology?
It is one of the drive health counters in Storage Manager > HDD/SSD > Health Info. Synology says a rising count, or a Drive re-identification (IDNF error) alert, points to an unstable connection caused by the drive or the drive slot.
Is a small Synology re-identification count a problem?
Synology says that if the count is stable, keep monitoring the drive. Removing and reinserting a drive can cause a slight increase.
How do I tell if the drive or the drive slot is bad on a Synology NAS?
Move the suspected drive to another working slot, or swap it with a healthy drive. If the errors follow the drive, replace the drive; if they stay with the slot, Synology recommends backing up and replacing the NAS.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.