NAS Codex › QNAP › QNAP warns an M.2 SSD reached its temperature threshold: what QNAP says to do

QNAP warns an M.2 SSD reached its temperature threshold: what QNAP says to do

QTS shows warning messages that an M.2 drive has reached its temperature threshold. QNAP's FAQ says it is fairly normal for an M.2 drive to run hot, and gives two fixes: cool the drive with a heat sink, and if the warning continues, compare the threshold with the drive maker's rated temperature. This page gives those steps and adds what QNAP says about M.2 heat and fan noise, and about a failed fan on a QM2 expansion card.

Written against: QTS 4.4.1 and later, all NAS series (QNAP FAQs last modified 2020-11-17, 2025-07-02 and 2026-03-16). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

QNAP recommends fitting a heat sink to the M.2 drive, either a QNAP heat sink or a third-party one that suits your SSD model. If the warning keeps appearing, look up the drive's normal operating temperature in its maker's specification. QNAP says the default threshold may be lower than that, and you can raise it at Storage & Snapshots > Disks/VJBOD: select the drive, click Disk Health, then Settings. If the M.2 drives sit on a QM2 card with a failed or noisy fan, see QNAP's fan steps below.

What the warning means

QNAP's FAQ applies to all NAS series on firmware 4.4.1 or later. It says it is fairly normal for an M.2 drive to reach a high temperature during operation, and that QNAP recommends installing heat sinks to keep M.2 drives cool.

Fix 1: fit a heat sink

QNAP says you can use a QNAP heat sink, sold through QNAP's online accessory store, or any third-party heat sink that is suitable for your SSD model.

QNAP's FAQ for the TVS-hx74 series (TVS-h474, h674, h874 and h874t) says where the heat sink should go: on the controller of the M.2 SSD, because the controller is the main source of heat. It says to check the SSD's technical documentation to find the controller. Each TVS-hx74 comes with two small heat sinks.

Fix 2: check the threshold against the drive's rating

If the message still appears after cooling, QNAP says:

  1. Find the normal operating temperature of the M.2 drive in its manufacturer's specification.
  2. Go to Storage & Snapshots > Disks/VJBOD.
  3. Select the drive and click Disk Health, then Settings.
  4. Set the threshold temperature higher. QNAP says the default threshold may be lower than the specification of the drive you are using.

Hot M.2 drives and a louder fan

QNAP's TVS-hx74 FAQ says that without proper cooling, a hotter M.2 PCIe NVMe SSD can make the CPU fan spin faster, which can make the whole system noisier. QNAP's two recommendations for that series:

M.2 drives on a QM2 card with a failed or noisy fan

QNAP's FAQ on QM2 expansion card fans covers the QM2-2P-344A, QM2-2P-384A, QM2-2P-244A, QM2-2S-220A, QM2-4P-384, QM2-2P2G2T, QM2-2P10G1TB and QMS-4S-240 (EOL). QNAP names three risks in replacing the fan yourself:

QNAP says that if the card is under warranty, or you are unsure about compatibility, contact QNAP Support or your reseller for RMA options first. If you go ahead yourself, QNAP's steps are:

  1. Back up important data from volumes or storage pools that use the QM2 card, plan a maintenance window, then power off the NAS and unplug the power cord before removing the card.
  2. Check the replacement fan against the original. QNAP lists 60 mm x 60 mm, 8 mm high, 12 V DC, 0 to 5,600 RPM (plus or minus 10%), with a 4-pin connector, and says specifications can vary slightly between QM2 models and hardware revisions.
  3. Fit the new fan on the same mounting points and connector, with the cable firmly connected and clear of other parts.
  4. Power on, confirm the fan spins with no abnormal noise, and check NVMe SSD temperatures and system health in QTS or QuTS hero.
  5. Monitor for at least 24 to 72 hours under a realistic workload. If you see abnormal temperatures, throttling or instability, shut down and recheck the fan installation and compatibility.

When to stop and get help

QNAP says not to power on the NAS before confirming the replacement fan's connector pinout and polarity, not to assume a fan is compatible because it looks the same size, and not to do any hardware replacement without a recent data backup. If the drive shows a SMART warning or error rather than a temperature warning, see disk SMART Warning or Error.

Questions

Is it normal for a QNAP M.2 SSD to get hot?

QNAP says it is fairly normal for an M.2 drive to reach a high temperature during operation, and recommends a heat sink, either QNAP's or a third-party one suitable for the SSD model.

Can I raise the M.2 temperature threshold on a QNAP NAS?

Yes. QNAP says to check the drive's normal operating temperature in the maker's specification, because the default threshold may be lower, then raise it at Storage & Snapshots > Disks/VJBOD > select the drive > Disk Health > Settings.

Why did my QNAP get louder after I installed M.2 SSDs?

QNAP's TVS-hx74 FAQ says a hotter M.2 PCIe NVMe SSD can make the CPU fan spin faster. It recommends a heat sink on the SSD controller and keeping the chassis installed, because removing it disrupts the airflow.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.