NAS Codex › QNAP › Expanding a QNAP storage pool by replacing disks with larger ones or adding disks

Expanding a QNAP storage pool by replacing disks with larger ones or adding disks

QNAP offers two ways to grow a storage pool without taking it offline: replace every disk in a RAID group with a larger one, one at a time, or add free disks to the RAID group. This page sets out QNAP's steps for both in QTS, and the QuTS hero version of the disk replacement, from two QNAP FAQs (last modified November 2025) and the QTS 5.1 user guide.

Written against: QTS 4.3.4 or later and QuTS hero h5.3.0 or later (QNAP FAQs last modified 2025-11-25 and 2025-11-27) and the QTS 5.1.x user guide. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

To use larger disks, go to Storage Manager, open the storage pool, select the RAID group, and choose Manage > Replace Disks One by One. Replace one disk, wait for the RAID group to finish rebuilding, then do the next. When every disk is replaced, click Expand Capacity. QNAP says this works for RAID 1, 5, 6 and 10, the data stays accessible, and the capacity is based on the smallest disk in the RAID.

Before you start

Replace disks with larger ones (QTS)

  1. Go to Storage Manager > Storage > Storage Space and double-click the storage pool. The Storage Pool Management window opens.
  2. Select the RAID group and click Manage > Replace Disks One by One.
  3. Select a disk to replace. QNAP says the new disk must have a greater capacity than the one it replaces.
  4. Click Change and wait until the disk description says Please remove this drive, then remove it. The NAS beeps twice.
  5. When the description says You can replace this drive, insert the new disk. The NAS beeps twice, and the disk and RAID group show Rebuilding.
  6. Wait for the rebuild to finish, then repeat for every disk being replaced.
  7. Click Expand Capacity, then Yes. The system expands the RAID group.

Replace disks with larger ones (QuTS hero)

  1. Open Storage Manager > Storage Space, find the storage pool, and click Manage under Action. Go to the RAID tab and identify the RAID group.
  2. Temporarily disable any hot spare disks (Disks > Device, select the spare, Action > Disable spare). QNAP explains this stops the system rebuilding the RAID group onto a spare before you insert the replacement.
  3. Have the same number of larger disks ready; each must be larger than the disk it replaces.
  4. Remove a disk. The NAS beeps twice and the RAID group shows Degraded.
  5. Insert the larger disk in the same bay. The NAS beeps twice and the RAID group shows Rebuilding.
  6. Wait until it shows Ready, then repeat for every disk. After the last rebuild, the RAID group and its storage pool are expanded.

Add disks to a RAID group instead

If the NAS has free disks, the QTS 5.1 user guide describes adding them to an existing RAID group while the pool stays online:

  1. Go to Storage & Snapshots > Storage > Storage/Snapshots, select the storage pool and click Manage.
  2. Select Action > Expand Pool, then Add new disk(s) to an existing RAID group, and choose the RAID group.
  3. Select the disks. QNAP warns that all data on the selected disks will be deleted.
  4. Click Expand, then OK. QTS rebuilds the RAID group, and the pool's capacity increases when the rebuild finishes.

When to stop and get help

Replace one disk at a time and wait for each rebuild. QNAP warns that removing any disk while the RAID group is rebuilding may cause permanent data loss or corruption. Adding disks wipes everything on the disks you add. If a rebuild does not start after you insert a disk, see rebuild not starting after drive replacement.

Questions

How do I increase storage on a QNAP NAS with bigger drives?

QNAP says to open the storage pool in Storage Manager, select the RAID group, choose Manage > Replace Disks One by One, replace each disk with a larger one and let it rebuild, then click Expand Capacity once all are replaced.

Why didn't my QNAP storage grow after replacing one disk?

QNAP says the storage capacity after replacing drives is based on the smallest drive in the RAID, so all the disks in the RAID group need replacing with larger ones before you expand capacity.

Can I add a disk to a QNAP RAID 1?

Yes. The QTS user guide says you can add free disks to a RAID 1, 5, 6, 50 or 60 group, but adding disks to RAID 1 changes it to RAID 5, and all data on the added disks is deleted.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.