NAS Codex › QNAP › QNAP NAS drives won't enter standby mode: what keeps them awake and how QNAP says to find it
QNAP NAS drives won't enter standby mode: what keeps them awake and how QNAP says to find it
Disk standby is on, but your QNAP NAS drives never spin down, or keep waking up. QNAP's FAQ says many built-in services and apps access the drives routinely and stop them entering standby. It gives two solutions: switch off the services and apps that are not needed, and if that is not enough, use QNAP's SSH script to find which file writes keep waking the drives. This page follows both, adds QNAP's other known causes, and gives QNAP's advice on whether to use standby at all.
Written against: QTS and QuTS hero (QNAP FAQs last modified 2020-09-17, 2022-06-24 and 2025-12-16). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Check that Control Panel > System > Hardware > Enable disk standby mode is ticked. Then work through QNAP's list: turn off UPnP port forwarding in myQNAPcloud, SMB if you do not use it, mapped drives on computers that keep the NAS busy, and the QNAP and third-party apps that poll the drives, such as Container Station, Download Station, Q'center, Security Center and Plex. If the drives still wake, run QNAP's standby_debug.sh script over SSH and disable the app whose files it shows being written. QNAP itself recommends a power schedule over standby mode.
First: should you use standby at all?
QNAP notes that while standby mode reduces power consumption, frequent spin-ups and spin-downs cause more wear and tear than constant spinning, which is a risk to disk health. QNAP therefore recommends setting a power schedule instead of using standby mode (see "Configuring the Power Schedule" in the QTS User Guide).
Make sure disk standby is enabled
- Log in to the NAS as an administrator and open Control Panel.
- Go to System > Hardware.
- Select Enable disk standby mode: The status LED will turn off if there is no access within, and choose the time.
- Click Apply.
Solution 1: turn off services and apps that keep the drives busy
Built-in services and setup
- UPnP port forwarding: open myQNAPcloud, click the top-right corner, confirm the warning with OK, select Auto Router Configuration and switch off UPnP Port Forwarding.
- Microsoft Networking: Control Panel > Network & File Services > Win/Mac/NFS/WebDAV, then deselect Enable file services for Microsoft Networking (SMB).
- Other devices: disconnect devices that do not need frequent access to the NAS.
- DMZ and port forwarding: turn these off on your router or firewall if the NAS is connected to the internet. QNAP says they expose the NAS to unsolicited access.
- Mapped shared folders: remove them on computers that constantly access the NAS.
- Wi-Fi dongle: connect the NAS with an Ethernet cable instead of a USB Wi-Fi dongle.
- Indexing and thumbnails: after you upload data, the NAS indexes files and generates media thumbnails. Depending on the number of files this can take a while, and the drives stay active until it finishes.
QNAP apps that can keep drives active
QNAP lists these, with its reason where it gives one. Disable the ones you do not need in App Center:
- AMIZcloud Agent: routinely collects system resources, status and performance data.
- Container Station: running containers keep the drives active.
- Download Station: running download or upload tasks keep the drives active.
- DA Drive Analyzer: regularly collects disk health information.
- HDP for SaaS: routinely accesses cloud services to sync and back up cloud data.
- HybridMount: File Cloud Gateway routinely accesses cloud services to sync files.
- NetBak Replicator: routinely searches for the NAS on the network.
- OceanKTV: routinely syncs recommended playlists with online databases.
- Q'center Agent: routinely collects disk health and monitoring information.
- Security Center: Security Advisory and Unusual File Activity Monitoring may keep the drives active when enabled.
- Also listed: Helpdesk, HBS 3 Hybrid Backup Sync, Multimedia Console, Media Streaming add-on, Notes Station 3, Q'center Server and QVPN Service.
Third-party apps
QNAP lists P2P apps, Mattermost, McAfee Antivirus and Plex Media Server.
Other causes QNAP names
An older QNAP FAQ on drives that keep waking up adds three causes:
- QNAP services such as Download Station and Music Station can run regular jobs that wake the disks from spindown. Check their configuration if they are active.
- Automatically synchronizing the NAS time with an internet time server can wake the drives.
- A system daemon running for RAID management (synchronizing).
Solution 2: find the app with QNAP's standby script
If turning things off does not work, QNAP's second solution identifies the app that stops the drives spinning down:
- Access the NAS over SSH.
- Run QNAP's command:
The terminal lists the most recently modified files. QNAP says the file at the bottom of the list may be what keeps the NAS from entering standby.cd /dev/shm; wget https://eu1.qnap.com/Storage/tsd/utility/standby_debug.sh -O standby_debug.sh ; sudo sh standby_debug.sh - When the terminal output stops updating, check that the status LED turns off. QNAP says this shows the drives entered standby.
- Open File Station, go to the Public folder, and download the new standby test log.
- Read the lines that say Last file modification. In QNAP's example, a write to a log under
.qpkg/Qcentershows Q'center stopped the disk spinning down. - Disable the app named in the file path (see "Enabling or Disabling an App" in the QTS User Guide).
External USB drives
QNAP says it is a system limitation that the NAS controls standby only for its internal drives, not external ones. It adds that an external drive should have no activity when nothing is reading from or writing to it, because it has no system partition.
When to stop and get help
QNAP says DMZ and port forwarding expose the NAS to unsolicited access. Deselecting SMB turns off the NAS's file services for Microsoft Networking, so check that nothing on your network relies on them first. QNAP lists a system daemon running for RAID management (synchronizing) as one cause of drives staying awake; if a rebuild never starts, see rebuild not starting after drive replacement.
Questions
Why won't my QNAP drives go into standby?
QNAP says many built-in services and apps access the drives routinely. It lists UPnP port forwarding, SMB, mapped drives, indexing and thumbnail generation, and apps such as Container Station, Download Station, Q'center, Security Center and Plex Media Server.
How do I find what keeps waking my QNAP drives?
QNAP's second solution is its standby_debug.sh script, run over SSH. It lists the most recently modified files and saves a standby test log in the Public folder, whose Last file modification lines show which app wrote to the drives.
Does QNAP recommend disk standby mode?
QNAP says frequent spin-ups and spin-downs cause more wear and tear than constant spinning and pose a risk to disk health, so it recommends a power schedule instead of standby mode.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.