NAS Codex › Synology › USB or external drive not detected or not working on a Synology NAS
USB or external drive not detected or not working on a Synology NAS
When a USB drive is not detected or cannot be opened on a Synology NAS, Synology's checklist covers where the drive should appear, which file systems DSM reads, a clean restart, and testing ports and the drive itself. This page combines that article with Synology's external drive FAQ and the DSM 7 help for External Devices.
Written against: Synology Knowledge Center articles for DSM 7 series and DSM legacy versions (last updated 2022-09-07 and 2025-12-03) and DSM 7 help. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Look for the drive in Control Panel > External Devices. DSM reads Btrfs, ext3, ext4, FAT32, exFAT, HFS Plus and NTFS; anything else shows as Not Supported. If it is not listed, shut down the NAS, unplug the power for 20 seconds, remove the USB device, power on, and plug the device back in. Then try a different USB port.
Step 1: is it listed?
Synology says every connected external storage device should appear under Control Panel > External Devices. When DSM can read a drive, it shares it through a shared folder named usbshare[number] (USB) or satashare[number] (eSATA), which is removed automatically when the drive is ejected.
Step 2: check the file system and size
- DSM recognizes Btrfs, ext3, ext4, FAT32, exFAT, HFS Plus and NTFS. A drive in any other format shows as Not Supported and no usbshare folder is created; it has to be formatted first. Some models support HFS Plus read-only, and a small number of models do not support Btrfs.
- If the drive's capacity is over the maximum single volume size for your NAS, Synology says it cannot be mounted.
Step 3: restart cleanly
- Shut down the NAS.
- Unplug the power cord for 20 seconds.
- Remove the USB device from the NAS.
- Power on the NAS.
- Plug the USB device back in.
Step 4: rule out the port and the drive
- Try a different USB 2.0 or 3.0 port. If the device works in one port but not another of the same type, Synology says that port may be damaged; contact your reseller for repair if the NAS is under warranty.
- If the NAS detects the device on a USB 2.0 port but not a USB 3.0 port, Synology says it could be a compatibility issue; check the Synology Products Compatibility List.
- Connect the device to a computer. If it does not work there either, it may be damaged.
- Connect other USB devices to the same NAS port. If none are detected, the port may be damaged.
The drive shows but something is wrong
- You cannot open the usbshare or satashare folder: Synology says this may be a file system problem on the drive. Connect it to a computer and run a file system check.
- You cannot format it: check it is properly inserted and not write-protected. DSM 7 help adds that formatting is unavailable while the drive is still initializing after being plugged in, while it is being formatted or backed up to, if it is damaged, or if it is under 1 GB (ext3/ext4).
- A "lost+found" folder appears: Synology says this is a normal system folder on ext3 and ext4 drives and advises against changing it.
- Other users cannot see it: in Control Panel > External Devices, Settings > Default Permissions sets Read/Write, Read only or No access for users and groups on external devices. Check also that Prohibiting the use of USB port under Settings > Advanced is not ticked, as it blocks all USB devices.
Formatting a drive for the NAS
In Control Panel > External Devices, select the drive, click Format, and follow the wizard. Synology says all data is deleted and cannot be restored, so back it up first. A drive formatted as ext4 is readable only by the Synology NAS; to read it directly on a PC or Mac, choose FAT32. The same page has a S.M.A.R.T. Test button to check the drive's condition. Always eject the drive before unplugging it.
When to stop and get help
Do not format a drive that holds data you need: Synology says formatting deletes everything permanently. If a drive works on a computer but not on any NAS port, check the compatibility list and contact your reseller about the ports. If you are trying to back up to the drive, see Hyper Backup restore-only and integrity check.
Questions
Why is my USB drive not detected by my Synology NAS?
Synology says to check Control Panel > External Devices, make sure the file system is supported, restart the NAS with the device unplugged, and try other USB ports and another computer to rule out a damaged port or drive.
Which USB drive formats does a Synology NAS support?
Synology says DSM recognizes Btrfs, ext3, ext4, FAT32, exFAT, HFS Plus and NTFS. Other formats show as Not Supported and need formatting first.
Why can't I open the usbshare folder on my Synology NAS?
Synology says this can come from a file system problem on the external drive, and suggests connecting it to a computer and running a file system check.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.