NAS Codex › Synology › Synology SSD cache Crashed, Degraded or Missing: Synology's steps by cache type
Synology SSD cache Crashed, Degraded or Missing: Synology's steps by cache type
Storage Manager says your SSD cache has degraded or crashed, or that it is missing. What happens to your data, and what you should do, depends on two things Synology spells out: whether the cache is read-only or read-write, and what status the volume behind it now shows. This page gives Synology's steps for each case.
Written against: Synology Knowledge Center articles for DSM 7 series and DSM legacy versions, and DSM 7 help (SSD Cache, Repair). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Read-only cache: Synology says there is no data loss, because it only holds copies. Remove the cache and create a new one with healthy SSDs. Read-write cache: check the volume first. Healthy: remove the cache and create a new one. Read-only: back up, remove and recreate the volume, restore, then create a new cache. Crashed: follow Synology's crashed-volume steps. A degraded read-write cache under RAID 1, 5, 6 or 10 protects itself automatically while it syncs its data to the drives. If DSM asks you to repair a cache group, use Manage SSD Cache Group > Repair.
Crashed, degraded and missing are different
- Crashed: Synology says an SSD cache crashes when the number of SSD failures exceeds the tolerable limit. That limit depends on the RAID type chosen when the cache was created.
- Degraded: Synology's article on degraded caches covers read-write caches under RAID 1, 5, 6 or 10 and describes an automatic protection mechanism (below).
- Missing: the system reports that the SSD cache is missing, which Synology handles separately.
Read-only cache crashed
Synology explains that a read-only cache stores frequently read data on the SSDs to speed up random reads, and that this data is a copy of data on the volume. So there is no data loss when an SSD fails. Its steps:
- Remove the SSD cache.
- Create a new SSD cache with healthy SSDs.
Read-write cache crashed: check the volume status first
A read-write cache is different: Synology says data is written to the SSDs first, to speed up random reads and writes. Its steps depend on the volume status in Storage Manager:
- Volume Healthy: remove the SSD cache, then create a new one with healthy SSDs. Synology says all services will work normally, without data loss.
- Volume Read-only: back up and remove the volume, create a new volume, copy the backed-up data to it, then create a new SSD cache with healthy SSDs.
- Volume Crashed: Synology points to its crashed-volume steps; see Volume crashed.
Removing an SSD cache is not instant. Synology's DSM 7 help says it may take several hours, depending on how much data is stored on the cache.
Read-write cache degraded: the automatic protection mechanism
Synology says that when a read-write cache under RAID 1, RAID 5, RAID 6 or RAID 10 degrades, DSM activates an Automatic protection mechanism (RAID 10 applies only to DSM 7.0):
- It stops caching new I/O and starts writing (synchronizing) the data already on the SSD cache to the hard drives.
- All services on the volume keep running normally during this process.
- New data goes straight to the hard drives instead of to the degraded cache.
When the synchronization completes, Synology says all services work normally without data loss, even if another SSD then crashes.
Repairing a cache group in DSM 7
If an SSD fails or another problem occurs in an SSD cache group, DSM 7 prompts you to replace the defective SSD and repair the group. Synology's help:
- Replace the defective SSD with a healthy one. It must be equal to or larger than the smallest SSD in the cache group.
- Go to Storage Manager > Storage and follow the Suggestion shown under the storage pool.
- If you are prompted to repair the cache group, click the pool's ellipsis icon and select Manage SSD Cache Group > Repair.
- Follow the wizard to finish.
Synology recommends SSDs on the Synology Products Compatibility List for your model. Its SSD cache help says SSDs not on the list may affect system stability and result in data loss.
SSD cache missing
If the system says the SSD cache is missing, Synology's steps are:
- Go to Storage Manager > Storage and identify the missing SSDs.
- Insert the required SSDs back into the NAS.
- Restart the NAS.
An older cache
Synology's DSM 7 help says SSD cache algorithms and features improve with each DSM version, and that a cache is up to date if it does not show a Not the latest version field. If your caches were created on an older DSM, Synology says you may want to remove them and create new ones.
When to stop and get help
Stop before removing anything if the cache is read-write and the volume is not Healthy. In that case, copy off what you can reach first. If the volume shows Read-only, Synology's steps start with a backup and end with removing and recreating the volume. If it shows Crashed, Synology sends you to its crashed-volume steps; see Volume crashed.
Questions
Will I lose data if my Synology SSD cache crashes?
Synology says a read-only cache holds only copies of volume data, so there is no data loss. For a read-write cache it depends on the volume: if the volume is Healthy, removing and recreating the cache causes no data loss; if it is Read-only or Crashed, Synology's steps involve a backup or its crashed-volume guidance.
What happens when a read-write SSD cache degrades?
Under RAID 1, 5, 6 or 10, DSM's Automatic protection mechanism stops caching new I/O and syncs existing cache data to the hard drives while services keep running. After the sync, Synology says there is no data loss even if another SSD crashes.
How do I repair an SSD cache group in DSM 7?
Replace the defective SSD with one equal to or larger than the smallest SSD in the group, then in Storage Manager > Storage follow the Suggestion and choose the pool's ellipsis > Manage SSD Cache Group > Repair.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-16.