NAS Codex › Synology › Synology link aggregation doesn't make transfers faster
Synology link aggregation doesn't make transfers faster
Link aggregation combines two or more LAN ports on a Synology NAS into a single Bond interface. It often leaves a single computer copying at exactly the same speed as before. Synology's Knowledge Center explains why, how to test it properly, and which feature is meant for speeding up one client.
Written against: DSM 7 Control Panel > Network > Network Interface (Synology KB articles last updated Dec 29, 2020 and Mar 13, 2024, plus the DSM 7 Link Aggregation help page). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Test with two or more computers at once. Synology says total bandwidth only increases with multiple clients, and each client is answered by one bonded interface. To speed up a single Windows client over SMB, Synology points to SMB3 Multichannel instead.
Why a single client does not speed up
Synology says the total network bandwidth only increases when there are multiple clients. Each client is answered by one of the bonded interfaces. Once an interface is assigned, all connections from that client use the same interface. Synology's comparison table says link aggregation improves the server's overall throughput but does not improve single-client throughput.
How to test it
Synology's test: upload or download a large file (for example a 4 GB movie) from two or more computers to the NAS at the same time. Watch the bandwidth in Resource Monitor > Performance in DSM, and compare it with the same transfer from a single client.
Check the Bond mode matches your switch
Create a bond in Control Panel > Network > Network Interface > Create > Create Bond. Link aggregation needs a model with at least two LAN ports. Synology's help describes the modes:
- Adaptive Load Balancing: balances traffic whether or not the switch supports link aggregation. Synology says not to enable link aggregation on the switch for this mode, even if it is supported.
- IEEE 802.3ad Dynamic Link Aggregation: requires IEEE 802.3ad (LACP) enabled on the switch. Multiple switches must be stackable and properly configured.
- Balance XOR: requires Static Link Aggregation on the switch. Without switch support, only traffic sent by the NAS is balanced.
- Active/Standby: fault tolerance only. Another port takes over if the active one goes down.
If the ports go to more than one switch, Synology says the switch ports must be in the same LAN or VLAN. With Open vSwitch enabled, the modes are Balance-SLB, Balance-TCP (LACP) and Active/Backup.
To speed up one client: SMB3 Multichannel
Synology describes SMB3 Multichannel as the feature for improving SMB performance for a single client. Link aggregation, by contrast, is for environments with many users and devices. Multichannel lets the server use several network connections at once. Synology says it enhances single-client throughput for the SMB service, but it applies to SMB only.
- Enable it: Control Panel > File Services > SMB > SMB Settings > Advanced Settings > Others > Enable SMB3 multi-channel.
- Adapters: it works when the NAS or the client has multiple adapters of the same speed. A single adapter helps only if it supports receive-side scaling (RSS). To get the most from it, the client's total throughput should match or exceed the NAS's.
- Balance the adapter count: Synology recommends that the number of adapters on the server divide evenly by the number on the client. Two 1Gb adapters on each side give two connections and up to 2Gb. Two on the server and three on the client give about 1.5Gb.
When to stop and get help
Synology notes that link aggregation still provides failover, keeping the NAS connected if one link goes down. That benefit applies even when a single client sees no speed gain.
Questions
Why doesn't Synology link aggregation speed up my PC?
Synology says total bandwidth only increases with multiple clients; each client is answered by one bonded interface, so a single client stays at the speed of one link.
How do I test Synology link aggregation?
Synology says to transfer a large file from two or more computers at the same time and compare the bandwidth in Resource Monitor > Performance with a single-client transfer.
What speeds up a single client on Synology?
Synology points to SMB3 Multichannel, enabled under Control Panel > File Services > SMB > Advanced Settings, which can enhance single-client SMB throughput with multiple adapters.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.