NAS Codex › Synology › Synology NAS file transfers are slow: Synology's checklist
Synology NAS file transfers are slow: Synology's checklist
Synology splits slow transfers into three places to look: the computer, the network between it and the NAS, and the NAS itself. This page sets out that checklist (last updated 2025-05-07), Synology's further steps for slow SMB transfers from Windows (last updated 2026-04-17), and its article on Windows real-time protection slowing SMB writes.
Written against: Synology Knowledge Center articles for DSM 7 series and DSM legacy versions (last updated 2025-05-07, 2025-05-23 and 2026-04-17). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Copy a large file (Synology suggests at least 5 GB) from a different computer. If that is just as slow, connect the computer to the NAS directly with an Ethernet cable instead of Wi-Fi, check in Control Panel > Network > Network Interface that the port shows the right speed (1000 Mbps on 1GbE), and make sure the MTU is the same on every device. Then check in Storage Manager that no storage pool is degraded or busy and the volume is under 90% full.
Check the computer
Synology says to transfer a file from another computer first. If speeds are consistent across computers, move on to the network. If not, or there is no other computer to test with, apply these on the computer:
- Its CPU and disk use should not be overloaded.
- Temporarily disable or remove firewall, antivirus and security software, and temporarily disable Microsoft Defender Advanced Threat Protection on Windows.
- Temporarily disable software with a performance impact (Windows Task Manager > Processes).
- Keep the network card driver up to date.
Synology has a separate article on Windows 10 real-time protection slowing SMB writes to the NAS. Its first method is to turn real-time protection off temporarily (it comes back on when the computer restarts) to see whether that is the cause. Synology notes that turning it off leaves the computer unprotected, and if it helps, recommends restoring the setting and installing third-party antivirus software as the permanent fix, since Microsoft Defender Antivirus turns off automatically when another antivirus is installed.
Check the network
- Use a wired network instead of Wi-Fi.
- Connect the computer and NAS directly with an Ethernet cable. Synology says that if the speed goes up, the router or switch may have a problem or wrong settings.
- In Control Panel > Network > Network Interface, check that the Network Status shows the right speed: 1000 Mbps for an RJ-45 1GbE port, 10000 Mbps for an RJ-45 or SFP+ 10GbE port.
- Check that the MTU is the same on the NAS, the computer and every device on the network. Synology says the default is 1500.
- Use a CAT5/e or better cable that is not bent or worn, and try another one.
Check the NAS
- Storage: in Storage Manager, repair any degraded storage pool first, and wait for running activities such as adding drives, changing the RAID type or repairing to finish. If the volume is over 90% used, free up space.
- Drives: use drives on the Synology Products Compatibility List, and do not mix PMR and SMR drives in one array. In Resource Monitor > Performance > Disk, click View All during a transfer; Synology says to replace a drive that is in bad status or has a much higher utilization than the others.
- CPU: in Resource Monitor > Performance > CPU, if usage is very high, find the service or process in Task Manager and stop it temporarily.
Synology adds that performance depends on the type and number of drives and the RAID configuration, and that RAID 0 and RAID 1 volumes have lower read and write performance on certain J series or Value series models because of their limited CPU.
Slow SMB transfers from Windows
If transfers are slow only over SMB from Windows, Synology's SMB article adds:
- Network: make the MTU identical to the computer's, or untick Set MTU value manually to return to the default. In Control Panel > Network > Traffic Control, disable rules that may affect SMB speed.
- SMB signing: turn it off on the NAS and the computers if it is on. In DSM 7.0 and above, Resource Monitor > Connections > Connected Users shows whether a connection is labeled "signing". Synology notes this may compromise system security.
- Encryption and checksums: encrypted folders can significantly increase CPU load and lower transfer rates, and checksum verification takes time; Synology suggests leaving Enable data checksum for advanced integrity unticked when creating a new shared folder for better transfer rates.
- SMB protocol settings: in Control Panel > File Services > SMB > Advanced Settings > General, set the maximum protocol to SMB2 with large MTU and the minimum to SMB2, and tick Enable Opportunistic Locking and Enable SMB2 lease.
- Logging: the more events the SMB transfer log records, the bigger the impact on speed. Untick Collect debug logs under Advanced Settings > Others.
- Indexing: temporarily disable file indexing in Universal Search and media indexing in Control Panel > Indexing Service.
- Scheduled tasks: disable scheduled backup tasks and scheduled Recycle Bin tasks, especially on Btrfs volumes.
- Other protocols: try a different file protocol. If that is slow too, Synology points back to the general checklist above.
When to stop and get help
Some of these steps lower security: Synology notes that turning off SMB signing may compromise system security and that turning off real-time protection leaves the computer unprotected, and it describes disabling security software as temporary. If the problem persists, Synology asks for logs from Support Center > Support Services > Log Generation with a support ticket. If the NAS is also slow to respond in DSM, see high CPU usage.
Questions
Why is my Synology NAS transfer speed slow?
Synology says to check the computer (test another PC, security software), the network (wired, direct cable, port speed, matching MTU, cable) and the NAS (degraded or busy storage pool, volume over 90% full, a slow drive, high CPU).
What speed should my Synology port show?
Synology says Control Panel > Network > Network Interface should show 1000 Mbps for an RJ-45 1GbE port and 10000 Mbps for an RJ-45 or SFP+ 10GbE port.
Which SMB settings does Synology suggest for faster Windows transfers?
Synology suggests SMB2 with large MTU as the maximum protocol, SMB2 as the minimum, Opportunistic Locking and SMB2 lease enabled, and debug logs turned off, under Control Panel > File Services > SMB > Advanced Settings.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.
- Synology Knowledge Center: What can I do with low data transfer rate?
- Synology Knowledge Center: What can I do if data transfer between Windows and my Synology system is slow over SMB?
- Synology Knowledge Center: Writing data via SMB becomes slower when "Real-time protection" is enabled on my Windows 10 computer. What can I do?