NAS Codex › Synology › Synology NAS has detected an IP conflict

Synology NAS has detected an IP conflict

DSM shows an IP conflict message, and a similar entry in Log Center, when it detects a conflict on one of the NAS's LAN ports. Synology says the cause is another device on the same local network configured with the same IP address as the NAS. Its article shows how to find that device and resolve the conflict, and the DSM network help shows where the NAS's address is set.

Written against: DSM 7 (Synology KB: My Synology NAS has detected an IP conflict; DSM 7 help: LAN/Internet; Synology KB: I can't connect to my Synology NAS on the local network). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

On a computer on the same network, run arp -a (Command Prompt as administrator on Windows, Terminal on macOS) and look for another device with the NAS's IP address. Change that device's address or the NAS's, and pick an unassigned IP for the NAS. The NAS's address is set in Control Panel > Network > Network Interface > Edit > IPv4.

What the message means

Synology says an IP conflict happens when another device in the same local network as your Synology NAS has the same IP address. DSM displays an error message when it detects the conflict at one of the LAN ports, and you may see a similar message in Log Center.

1. Find the device using the same address

Synology uses the ARP command, which lists all devices on the local network with their IP and MAC addresses in a table.

Check whether another device is listed with the same IP address as your Synology NAS.

2. Give one of them a different address

Synology's resolution is to change that device's IP address or the NAS's, to avoid further conflicts. It adds that an address may still be in use by another device, including one that is currently offline, and recommends using an unassigned IP address for the NAS.

3. Where the NAS's address is set

In DSM 7, go to Control Panel > Network > Network Interface, select the interface and click Edit. On the IPv4 tab:

Synology notes that a valid DNS server IP should be entered so that email notifications are delivered correctly through the SMTP server.

4. If you can't reach the NAS after changing it

The DSM help says that if you cannot connect to the NAS after changing these network settings, press the RESET button on the NAS to restore default settings. Synology's local-network troubleshooting article gives the method: press RESET for four seconds until you hear a beep. To find the NAS again, use Web Assistant (find.synology.com in a browser) or the Synology Assistant desktop utility; a status of Ready means the system is installed and ready to use.

5. Other settings on the same IPv4 tab

6. Basic connection checks

Synology's local-network troubleshooting article also lists these checks when the NAS can't be reached after a network change, such as a new router or internet provider:

When to stop and get help

Synology's troubleshooting article warns: if Web Assistant or Synology Assistant shows the NAS as Not installed, do not proceed with the installation, or all of your data will be deleted. If the NAS does not beep when you press RESET, Synology says it could be a hardware failure and to contact your reseller for RMA service if it is under warranty.

Questions

What does 'Synology NAS has detected an IP conflict' mean?

Synology says another device on the same local network has the same IP address as the NAS. DSM shows the message when it detects the conflict on a LAN port.

How do I find which device has the same IP as my Synology NAS?

Run arp -a in Command Prompt (as administrator) on Windows or in Terminal on macOS. Synology says it lists every device with its IP and MAC address.

How do I change the IP address of a Synology NAS?

In Control Panel > Network > Network Interface, select the interface, click Edit and use the IPv4 tab: DHCP, or Use manual configuration with an unassigned IP and subnet mask.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.