NAS Codex › Synology › Synology drive allocation status "Not Initialized": what it means and what to do
Synology drive allocation status "Not Initialized": what it means and what to do
Storage Manager lists a drive with the allocation status Not Initialized. On a brand-new drive that is normal. On a drive that was already holding your data, it is a warning sign. Synology lists three things the status can mean; which one applies decides whether you can use the drive straight away or should stop and work out where its data went.
Written against: Synology Knowledge Center articles with Environment DSM 6.2 to 7.1.1 (tagged DSM 7 series and legacy versions) and DSM 7 help (Assemble a Storage Pool). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
If the drive is brand new, Synology says you can use it directly: add it to a storage pool or set it as a hot spare. If it already held data, do not add it to a pool or create anything on it yet: Synology lists drive or hardware failure and human error as ways the system partition, DSM and the storage pool on a drive can be removed. Copy off what you can and check the rest of the pool first.
What "Not Initialized" means, per Synology
The allocation status shows whether a drive has DSM installed and how it has been assigned. Synology's status table defines Not Initialized as: "DSM is not installed on the drive. The drive can be assigned to a storage pool." Its dedicated article says the status may indicate that:
- The drive contains no system partition, so DSM is not installed on it.
- The drive is not in use and has not been assigned to a storage pool.
- The system partition, DSM and the storage pool on this drive have been removed because of a drive or hardware failure or human error.
For the other allocation statuses, Synology's table gives: Initialized (DSM installed, not yet in a pool), Normal (DSM installed and in a pool), Hot Spare, Detected (storage pool data found on the drive but the drive is not assigned to a pool; DSM 7 and above), System Partition Failed, Crashed and Deactivated. To see Synology's own explanation for a drive, point the cursor at the info icon next to Allocation status.
Scenario: the drive is brand new
Synology says you can proceed to use it directly, for example by adding it to a storage pool or setting it as a hot spare drive. Synology's storage pool help notes that installing a drive as a replacement erases all existing data on it.
Scenario: the drive came from another Synology NAS
For DSM 6.2 and earlier, Synology says to insert all the drives that belonged to that storage pool into the current NAS and restart. You may also need to repair the storage pool to bring it back to a healthy, accessible state.
On DSM 7, Synology's help describes Online Assemble: when drives from a pool created on another Synology NAS are installed, are not initialized, and are enough in number to assemble the pool, an Available Pool appears on the Storage page. To assemble it: go to Storage, click the Available Pool, click Online Assemble (or the upper-right icon, then Online Assemble), confirm and click Start. If it fails, the status changes to Assemble failed and Synology recommends restarting the system to assemble it.
Warning: the same help page explains how to remove an Available Pool, and says all data on all its drives is erased if you do. Assemble, do not remove, if you want the data.
Scenario: the drive was in use here and now shows Not Initialized
This is the third meaning in Synology's list: the system partition, DSM and storage pool on the drive were removed by a failure or by human error. Synology's article gives no repair step for this case. Treat it as a fault: back up whatever is still reachable, check the other drives' health on the HDD/SSD page, and see the drive status page for what each health status means.
When to stop and get help
Stop before adding a Not Initialized drive to a pool, creating a pool on it or removing an Available Pool if the drive may still hold data you need. Adding it erases it. If several drives in the same NAS suddenly show Not Initialized, or the pool shows Crashed or Missing, get help before going further.
Questions
Is "Not Initialized" bad on a new drive?
No. Synology says a brand-new drive can be used directly, for example added to a storage pool or set as a hot spare.
Will adding a Not Initialized drive to a pool erase it?
Synology's repair help says all existing data on a replacement drive will be erased. Do not add a drive that may still hold data you need.
What is the difference between Not Initialized and Detected?
Synology's table says Not Initialized means DSM is not installed on the drive. Detected (DSM 7 and above) means the system found storage pool data on the drive but the drive is not assigned to a pool.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-14.