NAS Codex › Synology › Synology data scrubbing: how long it takes and why the NAS slows down

Synology data scrubbing: how long it takes and why the NAS slows down

Data scrubbing is a DSM maintenance task that checks a storage pool and fixes data that is incorrect or incomplete. Synology recommends running it periodically, but on big drives it can run for a long time. Synology's Knowledge Center explains which pools support it, how to estimate the time, and how to schedule, pause or speed it up.

Written against: DSM 7 Storage Manager (Synology KB last updated Sep 29, 2026, plus the DSM 7 Data Scrubbing and RAID Resync Speed help pages). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

Go to Storage Manager > Storage, click Schedule Data Scrubbing and set a Time Grid so it runs only when you are not using the NAS. To stop a run for now, expand the storage pool and click Pause data scrubbing.

Which storage pools support data scrubbing

Synology's help says data scrubbing works only on Btrfs volumes, or on storage pools of these RAID types: SHR with three or more drives, RAID 5, RAID 6 or RAID F1. To see why a pool is not eligible, open Schedule Data Scrubbing. Pools that cannot be scrubbed are listed at the bottom with the reason, such as an incompatible file system, an incompatible RAID configuration or an abnormal storage pool.

Synology also notes that scrubbing cannot check and repair a shared folder unless data checksum for advanced data integrity is enabled for it (Control Panel > Shared Folder > Edit > Advanced). Without checksums, there is nothing to compare against.

How long it takes

Synology's estimate for storage operations, including data scrubbing, is:

Estimated time = capacity of a single drive รท speed of a single drive

Check drive capacity in Storage Manager > HDD/SSD. Synology uses binary units, so a drive shown as 10 TB is about 10,485,760 MB. System workload also matters: Synology says the more services run at the same time, the slower the operation may be. Its worked example, for adding a 10 TB hard drive, comes to about 291 hours at 10 MB/s while other services are running and about 58 hours at 50 MB/s without them. Drives in poor condition also lengthen the time.

Speed it up or limit the impact

Synology says the RAID resync speed limit is a global setting that also governs data scrubbing. Go to the Storage page > Global Settings > RAID Resync Speed Limits and choose one:

Synology's time estimates assume the recommended setting, and it says you can temporarily change it to speed up the process. Actual speed varies by model and drives.

Run, schedule or pause it

When to stop and get help

Synology lists a few things that stop or restart scrubbing. Changing the schedule cancels a run in progress and starts it again on the new schedule, and removing a pool from the schedule cancels its run. An improper shutdown during data writing stops scheduled scrubbing until the NAS is powered back on. A degraded pool is dropped from the schedule until it is repaired, and a crashed pool is removed permanently.

Questions

How long does Synology data scrubbing take?

Synology estimates it as the capacity of a single drive divided by the speed of a single drive, and says running other services at the same time slows it down.

Why can't I run data scrubbing on my Synology storage pool?

Synology says it works only on Btrfs volumes or SHR (3+ drives), RAID 5, RAID 6 or RAID F1 pools. The Schedule Data Scrubbing window lists ineligible pools with the reason.

Can I make Synology data scrubbing faster?

Synology says the RAID Resync Speed Limits global setting also controls data scrubbing; choosing Run RAID resync faster or a custom limit raises the speed.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.