NAS Codex › Synology › Can't sign in to a Synology NAS: IP address blocked and other login errors
Can't sign in to a Synology NAS: IP address blocked and other login errors
Synology says the error on the DSM login page tells you why sign-in failed. The most common lock-out is auto block, which blocks an IP address after too many failed logins. This page sets out how Synology says to remove that block, how auto block works, and what the other login error messages mean.
Written against: Synology Knowledge Center articles for DSM 7 series, DSM legacy versions and DSM Enterprise (last updated 2023-10-27 and 2026-09-17) and DSM 7 help. Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
If DSM says the IP address has been blocked, sign in as an administrator from a device with a different IP. Go to Control Panel > Security > Protection > Auto Block, click Allow/Block List, open the Block List tab, select the blocked IP and click Remove. If you have no other IP address to use, or have forgotten the password, Synology says to reset the administrator login credentials.
"This IP address has been blocked"
Synology says this appears when an IP address reaches the maximum number of failed logins allowed within a set time. You can still sign in from a different IP address. To remove the block:
- Sign in with an administrator account on a computer or phone that is not blocked. If you already know the blocked IP, skip to step 5.
- Untick Enable auto block in Control Panel > Security > Protection > Auto Block (DSM 7) or Control Panel > Security > Account > Auto Block (DSM 6.2).
- On the blocked device, sign in, click the person icon at the top right, and go to Personal > Security (DSM 7.2 and above) or Personal > Account > Account Activity (DSM 7.1 and earlier). Open Login History and note the IP address in the latest record.
- Back on the unblocked device, tick Enable auto block again.
- Click Allow/Block List, go to Block List, select the blocked IP, click Remove, then Delete.
How auto block works
Synology's DSM 7 help says auto block blocks IP addresses with too many failed logins to reduce the risk of brute-force attacks. It covers DSM, SSH, SMB, FTP, WebDAV, File Station, VPN Server, Synology Drive Server, Synology mobile apps and other services.
- In Control Panel > Security > Protection > Auto Block, set Login attempts and Within (minutes). Tick Enable block expiration and set Unblock after (days) to lift blocks automatically.
- Add trusted addresses to the Allow List (an IP, range, subnet or domain name). Synology says that if the NAS sits behind a reverse proxy, add the proxy's IP to the allow list.
- Because SMB clients log in automatically, Synology says auto block ignores the first few failed SMB attempts from each IP and only blocks public IP addresses. Since DSM 7.2, the SMB service supports auto block. Synology says no action is needed for blocked IPs you do not recognise; for ones you do, check why the logins failed.
Other login errors and what Synology says to do
- Account or password invalid: have an administrator reset your password in Control Panel > User & Group. If you are the only administrator, reset the administrator login credentials.
- Lost phone for verification codes (2FA, OTP or Adaptive MFA): sign in using a workaround, or disable and reset multi-factor authentication.
- "The disk space is full": Synology says the system partition (not your storage pool or volume) may be full. Shut the NAS down by holding the power button until it beeps, wait for the LED to stop flashing, and restart. If the message stays, contact Synology support.
- "System is getting ready. Please log in later": wait; start-up time depends on how many services run. The front LEDs show when it is ready.
- "Connection expired": the internet connection may be unstable; check the cable or try another network. Synology mentions Enhance browser compatibility by skipping IP checking in Control Panel > Security, but says it lowers the system's protection level.
- "You are not authorized to use this service": an administrator should check your privileges in Control Panel > Application Privileges > DSM > Edit.
- Stuck at "Processing. Please wait": causes include a poor connection, a very busy system or an IP change. Refresh, try another account or browser, clear the cache and disable extensions.
When to stop and get help
Removing a block or adding an IP to the allow list lets that address in again; Synology notes allowing a blocked IP may weaken the NAS's protection, so only do it for addresses you recognise. If you cannot sign in from anywhere because you forgot the admin password, see forgot admin password reset.
Questions
How do I unblock my IP address on a Synology NAS?
Synology says to sign in as an administrator from a device with a different IP, go to Control Panel > Security > Protection > Auto Block > Allow/Block List > Block List, select the IP and click Remove.
Why was my IP address blocked by Synology?
Synology says auto block blocks an IP after too many failed logins within the time you set. For SMB it ignores the first few failed attempts and only blocks public IP addresses.
What does "The disk space is full" mean at the Synology login page?
Synology says the system partition, not the storage pool or volume, may be full. Shut down by holding the power button until it beeps, wait for the LED to stop flashing, and restart; contact support if it persists.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.