NAS Codex › QNAP › QNAP Wake on LAN not working: settings and unsupported setups
QNAP Wake on LAN not working: settings and unsupported setups
Wake on LAN lets you power on a QNAP NAS that has been shut down by sending it a "magic packet". When it does nothing, QNAP's FAQs point to a few settings that must be in place and a short list of network setups where WOL is not supported at all. This page sets out both, plus what to do after a power cut.
Written against: QTS 4.3.6 and later (QNAP FAQs last modified 2022-03-30, 2022-08-22 and 2023-05-22). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
In Control Panel > System > Power, set EuP Mode Configuration to Disabled (QNAP says it is not possible to wake the NAS with EuP on) and set Wake-on-LAN (WOL) to Enable. Then check you are not using an unsupported port: QNAP lists 802.3ad (LACP) port trunks, 10G network cards and 2.5GbE connections on certain models.
Settings QNAP requires
- EuP Mode disabled: in Control Panel > System > Power, EuP Mode Configuration must be Disabled. This is the default, and QNAP calls it a very important step.
- WOL enabled: in the same place, Wake-on-LAN (WOL) must be set to Enable.
- Same network: for waking with Qfinder Pro, the computer and the NAS must be on the same LAN. QNAP also recommends giving the NAS a fixed IP address.
- A model that supports WOL: check the NAS's software specification, where Wake on LAN is listed under Power Management.
Where WOL is not supported
- 802.3ad dynamic LACP link aggregation (port trunking).
- 10G network cards.
- 2.5GbE connections on certain models. For example, on the TS-x31P3 series QNAP says the 2.5GbE port does not support WOL because of a hardware limitation, while the 1GbE port does. WOL also does not work when the 2.5GbE and 1GbE ports are combined in a port trunk.
Waking the NAS with Qfinder Pro
- Install Qfinder Pro and let it find the NAS, or add it manually.
- Press the power button to open Remote Wake Up, which sends a "magic packet" to the NAS. You can pick the device by name or enter its MAC address.
- Click Wake Up and wait for the NAS to start.
After a power cut or unplugging
QNAP says that if the power is physically removed, or there is an unexpected power failure while the NAS is off, Wake on LAN will not work, even after power returns. QNAP's instruction is to power the NAS on manually and then shut it down manually.
When to stop and get help
QNAP says that if EuP and WOL are set correctly and the NAS still will not wake, it could be a hardware issue, and to open a ticket with QNAP Service. If the NAS starts but cannot be found on the network, see Qfinder Pro cannot find the NAS.
Questions
Why doesn't Wake on LAN work on my QNAP NAS?
QNAP says EuP Mode must be disabled and WOL enabled under Control Panel > System > Power, and that WOL is not supported on 802.3ad LACP port trunks, 10G network cards or 2.5GbE connections on certain models.
Can I use Wake on LAN after a power failure on QNAP?
No. QNAP says that if power was removed or failed while the NAS was off, WOL will not work. Turn the NAS on manually and shut it down normally first.
Does the 2.5GbE port on a QNAP TS-x31P3 support Wake on LAN?
No. QNAP says the 2.5GbE port on the TS-x31P3 series does not support WOL because of hardware limitations, but the 1GbE port does.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.