NAS Codex › QNAP › QNAP volume shows "Cache Missing" after an SSD cache drive goes offline

QNAP volume shows "Cache Missing" after an SSD cache drive goes offline

When a QNAP NAS uses an SSD cache and one of the cache SSDs fails, comes loose or is removed, QTS can mark the volumes that use the cache as Cache Missing and stop serving them. QNAP says this is deliberate: it pauses access so the data you read always matches the data on the hard drives. You then choose whether to bring the SSD back or remove the cache.

Written against: QTS 5.0.x (QTS 5.0.x manual: Cache Missing, Removing a Missing SSD Cache, Removing the SSD Cache; QNAP article 2026-06-10; QNAP FAQ last modified 2022-06-24). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

If a cache SSD was pulled out or is loose, put it back in the same drive bay, then go to Storage & Snapshots > Cache Acceleration and accept the prompt to recover the cache volume. Only remove the cache if the SSD has failed: QNAP warns that removing a missing read-write or write-only cache deletes all write data that was not yet flushed to the hard drives.

Why QTS stops the volume

QTS offers three SSD cache modes, and QNAP explains that the risk differs between them:

For a write cache, the QTS manual says that if the cache disks become unavailable because of hardware failure or physical removal, every volume using the write cache becomes unavailable with the status Cache Missing. QTS restricts access because some volume data may be stored in the write cache without having been flushed to disk.

QNAP says QTS also suspends access to the volume when a read-only cache SSD goes offline unexpectedly, for example because of hardware aging or a poor connection. It cannot verify the cache's metadata at that point, and letting the volume run without the cache could leave the cache out of step with the drives when the SSD comes back.

Option 1: bring the SSD back

Use this when the SSD was removed or only lost contact. The QTS manual lists three ways to restore a missing cache:

QNAP's article on read-only caches describes the recovery after you reinsert the SSD:

  1. Go to Storage & Snapshots > Cache Acceleration.
  2. When the system prompts you to Recover Cache Volume, click OK.
  3. After the recovery, QTS automatically runs a file system check. Once data consistency is confirmed, the volume returns to normal access.

Option 2: remove the cache

The QTS manual says to delete a missing SSD cache only if it can't be restored, for example because a disk has failed. It warns that removing a missing write-only or read-write cache deletes all unflushed write data.

  1. Go to Storage & Snapshots > Storage > Cache Acceleration.
  2. Select Manage > Remove.
  3. Enter the admin password and click OK.
  4. Restart the NAS.
  5. Run a file system check on every volume that used the SSD cache.

For a read-only cache, QNAP says that if the SSD can't be recovered QTS shows "Unable to recover cache volume". After you remove the cache, the system flushes data and runs a file system check, then the volume returns to normal access with the original data intact. You can install a new SSD later and create the cache again.

Removing a working SSD cache

If the cache is healthy and you simply want to remove it, use Storage & Snapshots > Storage > Cache Acceleration > Manage > Remove and click OK. QNAP says QTS flushes all data in the cache to disk and then deletes the cache RAID groups, which may take a long time. It also warns that removing an SSD from the cache while write caching is enabled may cause data loss, so use the Remove option rather than pulling a drive.

Volumes unmounted after a firmware downgrade

QNAP says the SSD cache design in QTS 5.0 is not compatible with older QTS versions, so volumes that use an SSD cache become unmounted after downgrading from QTS 5.0. Upgrading back to QTS 5.0 brings them online. If you must downgrade, QNAP says to remove the SSD cache in QTS 5.0 first: turn off the SSD cache service and wait for flushing to finish, then click Manage and remove the cache.

Keep a cache SSD failure from stopping the volume

QNAP says a single SSD or RAID 0 is technically viable for a read-only cache, but one failed SSD then stops access until you step in. If you need the volume to stay online, QNAP recommends building the cache on a RAID level with redundancy, such as RAID 1 or RAID 5, so the cache keeps running on its remaining members until you replace the failed SSD.

When to stop and get help

If you use a read-write or write-only cache and the SSD can't be brought back, remember that QNAP says removing the missing cache deletes unflushed write data. If you need help, QNAP says to contact its technical support team.

Questions

Why does my QNAP volume say Cache Missing?

QNAP says QTS marks volumes Cache Missing and restricts access when the SSD cache disks they use become unavailable, because some data may still be in the cache and not yet on the hard drives.

How do I fix Cache Missing on a QNAP NAS?

If the SSD was removed or loose, reinsert it in the same bay, resolve any RAID errors or restart the NAS, and accept Recover Cache Volume in Storage & Snapshots > Cache Acceleration. Remove the cache only if the SSD can't be restored.

Will removing a missing SSD cache lose data?

For a read-write or write-only cache, QNAP warns that removing a missing cache deletes all unflushed write data. For a read-only cache, QNAP says the original data on the hard drives stays intact.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.