NAS Codex › QNAP › QNAP NAS file transfers are slow: how QNAP says to find the cause
QNAP NAS file transfers are slow: how QNAP says to find the cause
QNAP's troubleshooting for slow transfers works from the network inward: test raw network throughput, then the link and cabling, then MTU, then background jobs, then the storage itself. This page combines that FAQ (last modified 2026-03-31) with QNAP's older FAQ on read and write speed and its FAQ on SMB signing on macOS.
Written against: QTS and QuTS hero (QNAP FAQs last modified 2022-08-24, 2024-08-07 and 2026-03-31). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Run an iperf3 test between the NAS and your computer. QNAP expects about 940 Mbps (about 117 MB/s) on 1GbE and about 9.4 Gbps on 10GbE. If that is low, the network is the bottleneck: check the link speed and duplex, the cable and switch port, and that the MTU matches on the NAS, switch and computer. If iperf3 is normal, look at scrubbing and backup jobs running at the same time, then at the disks.
What speed to expect
QNAP's FAQ on dramatic speed drops gives the iperf3 results to expect on a healthy link:
- 1GbE: about 940 Mbps (about 117 MB/s)
- 10GbE: about 9.4 Gbps (about 1.17 GB/s)
- 25GbE: about 23.5 Gbps (about 2.9 GB/s)
Step 1: test the network on its own
QNAP calls an iperf3 test, which measures the network without any file protocol, the most important first test. Run the iperf3 server on the NAS and the client on your computer. If the result is low, the network path is the bottleneck. If it is normal, QNAP says the physical network is likely fine and the problem is in the file service layer, so go to step 4.
Step 2: isolate the network path
QNAP says not to test with link aggregation or multipathing active: test one NIC, one cable and one switch port at a time.
- Link speed and duplex: in Control Panel > Network & Virtual Switch > Interfaces, check Speed and Duplex for each adapter. QNAP notes a 10GbE NIC that has negotiated down to 1GbE caps throughput at about 117 MB/s, and half duplex can reduce it significantly. If the speed is unexpected, try a different cable or switch port.
- Errors: non-zero receive or transmit errors, drops or overruns on an interface can point to the cable, the SFP module or the switch port.
- Cabling: swap the DAC cable or SFP module for a known-good one, connect the NAS straight to the computer to rule out the switch, or try another switch port. QNAP's older FAQ also says the cable must meet the requirement, for example CAT6 for a 1000Mbps network.
Step 3: check the MTU matches everywhere
QNAP says an MTU mismatch between the NAS, the switch and the computer is a common cause of throughput collapse. All three must use the same MTU. As a quick test, set the MTU to 1500 on all of them and test again; if speed improves, jumbo frames are likely misconfigured. Jumbo frames (MTU 9000) must be enabled on the NAS, the switch port and the computer's network card.
Step 4: look for background jobs
QNAP says scheduled pool scrubbing and scheduled backup jobs can use a lot of disk I/O, so if the slowdown happens at predictable times (nightly or weekly, for example) check their schedules first.
- Scrubbing: go to Storage & Snapshots > Storage/Snapshots, select the storage pool, and click Manage > Actions to see the schedule. QNAP says scrubbing reads every block on every disk and can cut transfer performance by 50% or more while it runs.
- Backups: HBS 3, RTRR, rsync and Snapshot Replica jobs compete with your transfers for disk I/O and network bandwidth. Check active and scheduled jobs in HBS 3 and any third-party backup software.
Step 5: check the disks and storage settings
- In Storage & Snapshots > Storage > Disk/VBOD > Performance Test, run a Sequential Read Test. QNAP says to replace a disk with low speed, for example less than 80 MB/s.
- Check the SSD cache under Storage & Snapshots > Cache Acceleration; QNAP says a degraded cache can throttle I/O. Check the disks' S.M.A.R.T. health too.
- Disable unused apps in App Center to free resources.
- QNAP lists settings that affect speed: encryption slows it down (use a non-encrypted shared folder and volume, and disable SMB encryption if it is on), and SSDs, a static volume, and RAID 0 or RAID 6 can improve throughput.
Slow writes from your computer
QNAP's older FAQ says slow writes can also come from the computer itself: its own disk may be slow, or its Ethernet port may not be giving enough speed. On Windows you can check the link speed with the Get-NetAdapter command in PowerShell; on macOS, in the network settings.
Mac users: SMB signing
QNAP says SMB signing is on by default on macOS 10.11.5 to 10.13.3. It makes file transfers more secure but uses more system resources. QNAP's FAQ shows how to turn it off by creating an /etc/nsmb.conf file on the Mac containing [default] and signing_required=no, and how to turn it back on by deleting that file. QNAP notes that disabling SMB signing can decrease the security of file transfers.
When to stop and get help
QNAP warns not to make several changes at once: change one thing, test again, and record the original settings first, especially network, MTU and switch settings. It also says SMB results alone are not enough to find the cause; if every protocol is slow, start with the network tests. If the web interface is slow as well, see high CPU usage or a slow web interface.
Questions
What transfer speed should a QNAP NAS reach on 1GbE?
QNAP says an iperf3 test on a healthy 1GbE link should show about 940 Mbps, which is about 117 MB/s. On 10GbE it expects about 9.4 Gbps.
Why did my QNAP NAS suddenly get slow?
QNAP lists network causes (link negotiated down, bad cable or port, MTU mismatch), background jobs such as pool scrubbing and backups, and storage issues such as a slow disk or degraded SSD cache. It says to test the network with iperf3 first.
Can RAID scrubbing slow down my QNAP NAS?
Yes. QNAP says scrubbing reads every block on every disk and can reduce transfer performance by 50% or more while it runs. Check the schedule under Storage & Snapshots > Storage/Snapshots > Manage > Actions.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.