NAS Codex › QNAP › Can't access QNAP shared folders from Windows File Explorer (SMB): QNAP's checklist

Can't access QNAP shared folders from Windows File Explorer (SMB): QNAP's checklist

Windows File Explorer cannot open, or cannot see, the shared folders on a QNAP NAS over SMB. QNAP says many possible issues on either the NAS or the SMB client can cause this, and its FAQs give a checklist for each side, plus two specific cases: Windows not finding the folders since Windows 10 version 1709, and older QTS with Windows 11 24H2. This page puts them together in QNAP's order.

Written against: QTS and QuTS hero (QNAP FAQs last modified 2022-12-08, 2024-10-25 and 2026-07-07). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

On the NAS: update the firmware, check the files open in File Station, enable SMB in Control Panel > Network & File Services > Win/Mac/NFS/WebDAV > Microsoft Networking, check the user's shared folder permissions, and make sure QuFirewall or Control Panel > Security is not blocking the PC. On Windows: be on the same network, turn off Windows Hello sign-in, remove the NAS's saved credentials from Credential Manager, then close File Explorer, run net use * /y /d and remap the drive with Qfinder.

On the QNAP NAS

QNAP's FAQ on shared folders that Windows File Explorer cannot access says to work through each of these on the NAS:

  1. Update the NAS to the current firmware.
  2. Confirm the files are accessible in File Station.
  3. Enable SMB in Control Panel > Network & File Services > Win/Mac/NFS/WebDAV > Microsoft Networking.
  4. Configure the highest and lowest SMB version in Microsoft Networking > Advanced Options. QNAP notes that, for security reasons, the highest SMB version is SMB 3 and the lowest is SMB 2. Some legacy devices only support the less secure SMB 1; for those, you must change the lowest SMB version to SMB 1.
  5. Grant folder permissions to the NAS user in Control Panel > Privilege > Shared Folder, by editing the shared folder permissions.
  6. Remove all entries from the shared folder's Microsoft Networking host access list: in Control Panel > Privilege > Shared Folder, click Edit and go to that tab.
  7. Remove any network blocks. Check whether QuFirewall is blocking the client, and in Control Panel > Security remove the client from the Allow/Deny list.

On the Windows PC

QNAP's client-side checks are:

  1. Confirm the NAS and the PC are on the same network.
  2. Disable Windows Hello Authentication in Windows 10 or 11, so the PC does not use a Microsoft Account over the SMB share.
  3. Map the network drive using Qfinder.
  4. Remove your QNAP NAS credentials from the Windows Credential Manager.

If the problem persists, QNAP says to release the current network drive connection and remap it: quit all File Explorer windows, run net use * /y /d from the command line, then remap the network drive using Qfinder.

Shared folders not showing since Windows 10 version 1709

A second QNAP FAQ explains that starting from Windows 10 version 1709 (Fall Creators Update), Windows no longer supports SMB version 1 by default. That stops File Explorer from discovering shared folders on a NAS running QTS or QuTS hero 4.3.4 or earlier on the local network.

QNAP's first method, for QTS or QuTS hero 4.3.4 and later, is to enable WS-Discovery. QNAP says WS-Discovery finds shared folders on the local network even if the PC has SMB 1 disabled or removed, and it picks the most suitable SMB version for the PC and the NAS. Log in as an administrator, go to Control Panel > Network & File Services > Win/Mac/NFS > Advanced Options and enable WS-Discovery. You can also set the highest and lowest SMB versions it uses. QNAP strongly recommends not using SMB 1, because it has critical security vulnerabilities, and says to install SMB 1 in Windows only if the NAS does not support QTS or QuTS hero 4.3.4 or later.

To open the folders, press Windows key + R and enter two backslashes followed by the NAS's IP address, for example \\174.37.2.100. QNAP says the IP address is shown on the NAS's LCD screen, or in Qfinder Pro (select the NAS and click Network Drives). To map a folder as a drive, open File Explorer, go to This PC, choose Map network drive, enter the same address and pick a drive letter.

QTS 4.3.3 or 4.3.4 with Windows 11 24H2

QNAP has a FAQ for one more case. After upgrading to Windows 11 version 24H2, shared folders on a NAS running QTS 4.3.3 or 4.3.4 may not open if the credentials were not entered in Windows Credential Manager beforehand. QNAP says this is due to stricter network authentication in Windows 11 24H2, and that these older QTS versions lack modern SMB features, so they cannot complete authentication without pre-configured credentials.

QNAP's fix is to add the credentials by hand:

  1. Press Windows + S, type Credential Manager and open it.
  2. Click Windows Credentials, then Add a Windows credential.
  3. Enter the NAS's IP address or host name, your NAS user name and your NAS password, and save.
  4. Open File Explorer and go to the NAS by its IP address.

If none of this works

QNAP's last step before contacting support is to run net use Z: \\NAS_IP_address\Public /user:Username, using a user name that has permission for the Public folder, and note the errors it returns for QNAP support.

When to stop and get help

Do not lower the minimum SMB version to SMB 1 unless a legacy device needs it: QNAP says SMB 1 has critical security vulnerabilities, and WS-Discovery finds the shared folders without it on QTS or QuTS hero 4.3.4 and later. If Qfinder Pro cannot find the NAS at all, see Qfinder Pro can't find your QNAP NAS.

Questions

Why can't I access my QNAP shared folders from Windows?

QNAP says the cause can be on the NAS or the PC. On the NAS, check SMB is enabled, the SMB versions, folder permissions, host access entries and QuFirewall. On Windows, check the network, Windows Hello sign-in and the saved credentials in Credential Manager.

Why don't my QNAP shared folders show in File Explorer?

QNAP says Windows 10 version 1709 and later no longer support SMB 1 by default, which stops discovery on QTS or QuTS hero 4.3.4 or earlier. On 4.3.4 and later, enable WS-Discovery in Control Panel > Network & File Services > Win/Mac/NFS > Advanced Options.

Should I enable SMB 1 on my QNAP?

QNAP strongly recommends not using SMB 1 because of critical security vulnerabilities. Its default range is SMB 2 to SMB 3; change the lowest version to SMB 1 only for legacy devices that support nothing else.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.