NAS Codex › QNAP › QNAP NAS keeps restarting after adding memory: how to test the RAM

QNAP NAS keeps restarting after adding memory: how to test the RAM

After you add or replace memory in a QNAP NAS, QNAP says the NAS may fail to finish booting or keep restarting without powering up fully. Its troubleshooting FAQ gives a short order of checks, and two more FAQs explain how to run a memory test: from a bootable USB on Intel, AMD and Zhaoxin models, or with the memtester utility on any model running QTS or QuTS hero.

Written against: QTS and QuTS hero (QNAP FAQs last modified 2025-11-17, 2025-10-13 and 2025-09-18). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

QNAP's order: make sure the modules are compatible with your model and are certified QNAP memory, reseat them, then put the original memory back. If the NAS boots normally with the original modules, QNAP says the new memory may be incompatible or faulty. Then run a memory test, and contact QNAP support if nothing helps.

1. Check compatibility

QNAP says to make sure the memory modules are compatible with your specific NAS model, and that you are using certified QNAP memory. It warns that third-party or uncertified memory may cause instability.

2. Reseat the modules

  1. Power off the NAS and disconnect it from power.
  2. Open the chassis as your NAS hardware manual describes. QNAP suggests an anti-static wrist strap and handling the memory by its edges.
  3. Remove the modules and reinstall them carefully, making sure each is securely seated in its slot.
  4. Reconnect power and start the NAS.

3. Try the original memory

If you replaced existing memory, reinstall the original modules and power on. If the NAS starts normally, QNAP says the new memory may be incompatible or faulty.

4. Run a memory test

Bootable USB (Intel, AMD and Zhaoxin models)

QNAP says this method only applies to NAS models with an Intel, AMD or Zhaoxin CPU.

  1. On a PC, download the latest Auto-installer for USB Key from memtest.org, extract it, and run it to make a bootable USB flash drive.
  2. Power off the NAS and remove all the hard disks.
  3. Connect a VGA or HDMI monitor, a USB keyboard and the bootable USB drive.
  4. Power on and press DEL to enter BIOS setup. In the Boot settings, set the first boot device to your USB flash drive. QNAP notes that if two USB devices appear, don't select "USB DISK MODULE PMAP".
  5. Go to Save and Exit. The memory test starts automatically.

memtester, without a monitor (all QTS and QuTS hero models)

QNAP's second method runs the memtester utility on the NAS itself. It says faulty memory can cause system instability or data corruption, and gives these cautions before you start:

The steps are: save the memtester files to the Public shared folder, stop all NAS services, check the free memory, run the memtester build that matches your platform (x64, armv7 or arm64) with a memory size and number of loops, read the results, start all NAS services again, and remove the utility when you no longer need it. QNAP says repeated FAILURE lines mean the memory module may be defective and should be replaced.

5. Contact QNAP support

If none of these steps help, QNAP says to contact its technical support. It also notes that most user guides don't include detailed memory troubleshooting, so check your model's hardware manual or the QNAP support website for model-specific hardware steps.

When to stop and get help

QNAP's memtester method stops every NAS service while it runs, and QNAP says to back up important data first. The bootable-USB method needs all hard disks removed from the NAS before the test.

Questions

Why does my QNAP NAS keep restarting after I added RAM?

QNAP says new modules may be incompatible, uncertified or not seated properly. Reseat them, then try the original memory; if it boots, the new memory may be faulty.

How do I run a memory test on a QNAP NAS?

On Intel, AMD and Zhaoxin models, boot a memtest USB with the disks removed. On any QTS or QuTS hero model, QNAP also documents running memtester on the NAS.

What does FAILURE mean in a QNAP memtester result?

QNAP says repeated FAILURE messages mean the memory module may be defective and should be replaced.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.