NAS Codex › QNAP › QNAP NAS reboots on its own or hangs: QNAP's order of checks
QNAP NAS reboots on its own or hangs: QNAP's order of checks
Your QNAP NAS restarts by itself, or freezes and stops responding. QNAP's FAQ for unexpected reboots and system hangs gives an order of checks, from memory to apps to SSD cache to the disks. Two more QNAP FAQs cover what comes next: how to run a memory test, and how to tell from the startup beep whether the NAS hardware has failed.
Written against: QTS and QuTS hero, all NAS series (QNAP FAQs last modified 2022-06-24 and 2025-10-13). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Work through QNAP's list in order and stop when the problem stops: put back the memory the NAS shipped with if you changed it; disable all third-party apps in App Center, then all QNAP apps, re-enabling them one by one to find the cause; turn off SSD cache in Storage & Snapshots > Storage > Cache Acceleration; check the disks against QNAP's compatibility list; then run a bad block scan and a SMART complete test on each disk. If the disks pass, contact QNAP support through the Service Portal.
Step 1: check the memory
QNAP's first step is the memory. If you changed the memory modules, put back the original modules the NAS shipped with. QNAP says to use only QNAP memory modules to keep the system stable, and for NAS models with more than one memory slot, to use QNAP modules with identical specifications. It warns that unsupported modules may degrade performance, cause errors, or stop the operating system from starting.
Step 2: disable third-party apps
- Log in to QTS as an administrator and open App Center.
- Disable all third-party apps.
- If the reboots or hangs stop, enable the third-party apps one at a time to find which one causes it. If they continue, go to Step 3.
Step 3: disable QNAP apps
Repeat the same test with QNAP's own apps: disable all QNAP apps in App Center. If the problem stops, enable them one at a time to confirm the cause. If it continues, go to Step 4.
Step 4: turn off SSD cache
If SSD cache is enabled, go to Storage & Snapshots > Storage > Cache Acceleration and turn it off. QNAP says that if the problem no longer recurs, remove the SSD cache and create it again. If it still recurs, go to Step 5.
Step 5: check the disks are compatible
In Storage & Snapshots > Storage > Disks/VJBOD, note each disk's model and compare it with QNAP's compatibility list. Replace any disk that is not compatible.
Step 6: test the disks
- In Storage & Snapshots > Storage > Disks/VJBOD, check the status of every disk.
- Click Action > Scan for Bad Blocks.
- Click Disk Health > Test > Complete Test.
- If a disk problem is reported, replace that disk. If the disks pass, QNAP says to contact QNAP support through the Service Portal.
Running a memory test
QNAP has a separate FAQ on testing the memory, for NAS models with Intel, AMD or Zhaoxin processors:
- On a PC, download the "Auto-installer for USB Key" file from memtest.org, extract it, and run it to create a bootable USB flash drive.
- Power off the NAS and remove all the hard disks.
- Connect a VGA or HDMI monitor, a USB keyboard and the bootable USB drive to the NAS.
- Power on the NAS and press DEL to enter the BIOS setup. On the Boot settings screen, set the USB flash drive as the first boot device (QNAP notes that if two USB devices appear, do not select "USB DISK MODULE PMAP").
- Choose Save and Exit. QNAP says the memory test starts automatically.
QNAP links a second method for models without HDMI or a GPU, which uses the memtester utility.
If the NAS does not beep at startup
QNAP's hardware-failure FAQ says the NAS beeps during startup to show that its Power-On Self-Test passed, and this beep cannot be turned off. If there is no beep, QNAP says the NAS has a hardware failure and needs repair. If it is under warranty, contact the reseller or distributor for RMA; if it has other symptoms or is out of warranty, contact QNAP support. For an end-of-life model, QNAP suggests considering a newer device and migrating the data.
When to stop and get help
Remove disks only when QNAP's steps call for it (the memory test does), and power the NAS off first. Disabling apps and SSD cache are tests: turn back on what turned out not to be the cause. If the NAS also shows high CPU or a slow web interface, see high CPU or slow web interface.
Questions
Why does my QNAP NAS keep rebooting?
QNAP's FAQ checks, in order: memory modules (put back the originals), third-party apps, QNAP apps, SSD cache, disk compatibility, and finally a bad block scan and SMART complete test on each disk.
Can non-QNAP memory cause reboots?
QNAP says to use only QNAP memory modules, with identical specifications in multi-slot models, and warns that unsupported modules may degrade performance, cause errors, or prevent the operating system from starting.
How do I know if my QNAP NAS hardware has failed?
QNAP says the NAS beeps at startup when its Power-On Self-Test passes. If there is no beep, the NAS has a hardware failure and needs repair through the reseller (in warranty) or QNAP support.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.