NAS Codex › QNAP › QNAP port trunking (link aggregation) not increasing transfer speed

QNAP port trunking (link aggregation) not increasing transfer speed

Port trunking, also called link aggregation or LACP, combines two or more LAN ports on a QNAP NAS into one group. A common surprise is that a single computer copying a file is no faster afterward. QNAP's own tutorials and FAQ explain why: trunking adds total bandwidth for several clients at once, not speed for one.

Written against: QTS Network & Virtual Switch port trunking (QNAP tutorials last modified 2017-03-20 and 2020-08-21; FAQ last modified 2022-06-24). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

Test with two computers at once. QNAP's FAQ says to set the two 1Gbps adapters to 802.3ad mode and have two clients read or write different files to or from the NAS share at the same time. A single client will not go faster than one link.

Why one computer does not get faster

QNAP says port trunking cannot break the speed limit of a single Ethernet device. It gives enough bandwidth for several users connecting at the same time. QNAP's example: with two 1Gb ports trunked, the aggregated bandwidth rises to 2Gb, but the network speed stays 1Gb.

QNAP's test results in its 802.3ad tutorial show the difference. On a single Gigabit link, two users downloading at the same time reached 108 to 110 MB/s in total. With two Gigabit links aggregated, two users downloading at the same time reached 210 to 223 MB/s, and uploading 200 to 210 MB/s.

QNAP's unmanaged-switch tutorial shows how this works in Balance-alb mode. QTS assigns a fixed interface to each client in the order they connect, and the assignment does not change until a client disconnects. A third client shares an interface with the first.

QNAP also notes that available system resources and the maximum read/write speed of the NAS's drives greatly affect overall bandwidth.

Check the trunking setup

Set up 802.3ad port trunking

  1. Open Network & Virtual Switch, go to Interfaces and click Port Trunking.
  2. Click Add and select two or more interfaces connected to the same switch.
  3. Choose the switch type and the trunking mode (802.3ad for a switch with LACP).
  4. For 802.3ad, click the settings button beside it and choose the hash policy.
  5. Click Apply. The group appears on the Port Trunking page.

How to test it properly

QNAP's tutorial tests by sending files from two computers to the NAS at the same time, then watching network activity in Resource Monitor. Each client should use a different interface, and the combined total should go above what one link can carry.

When to stop and get help

QNAP notes that port trunking also gives failover: if one network port fails, the NAS keeps its connection on the other. That benefit applies even with a single client.

Questions

Why didn't QNAP port trunking double my transfer speed?

QNAP says port trunking cannot break the speed limit of a single Ethernet device. Two trunked 1Gb ports give 2Gb of total bandwidth for several clients, but one client still gets 1Gb.

How do I test QNAP port trunking?

QNAP says to use two clients reading or writing different files to or from the NAS at the same time, and watch network activity in Resource Monitor.

Which QNAP port trunking mode should I use?

QNAP recommends 802.3ad dynamic with a managed switch that supports LACP; its unmanaged-switch example uses Balance-alb.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.