NAS Codex › QNAP › QNAP NAS IP address changes after a reboot, or conflicts on the network
QNAP NAS IP address changes after a reboot, or conflicts on the network
When a QNAP NAS takes its address from DHCP, it can come back from a power outage or reboot with a different IP, and PCs that use the old address can no longer connect. QNAP's FAQs give two ways to keep the address fixed, what to check when Windows still can't find the NAS by name, and one case where Container Station causes an IP conflict.
Written against: QTS and QuTS hero networking (QNAP FAQs last modified 2025-06-05, 2025-08-27, 2025-09-03 and 2025-11-14). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Find the NAS with Qfinder Pro, then fix its address. QNAP's preferred way is a DHCP reservation on your router that binds the NAS MAC address to one IP, with the NAS left on Obtain IP address automatically (DHCP). The alternative is a static IP on the NAS in Control Panel > Network & Virtual Switch > Network > Interfaces > Configure, outside the router's DHCP pool.
1. Find the NAS's current address
QNAP says to use Qfinder Pro to discover NAS devices on the LAN, even if you don't know the IP.
2. Preferred: a DHCP reservation on the router
By default, DHCP assigns addresses dynamically, and they can change each time the lease is renewed. QNAP's preferred fix is a DHCP reservation (also called a Reserved IP table) on your router, which binds the NAS's MAC address to one IP so it receives the same address after reboots and lease renewals.
- Find the MAC address: log in to QTS or QuTS hero as an administrator, go to Control Panel > Network & Virtual Switch, select the Ethernet interface (for example, Adapter 2) and note its MAC address.
- Add the reservation on the router: in the router's management interface, add a reservation for that MAC address with the IP you want, then apply. On a QNAP QHora-301W the location is Network > Bridge Settings > DHCP Settings > Reserved IP Table; QNAP says other routers differ, so check your router's documentation.
- Set the NAS to DHCP: in Control Panel > Network & Virtual Switch, select the Ethernet interface or Virtual Switch, choose Obtain IP address automatically (DHCP) and click Apply.
- Restart the NAS and the router so the NAS receives the reserved address.
If the NAS has several network interfaces, QNAP says to repeat this for each one. QNAP's limits: make sure no other device uses the reserved IP, and reconfigure the reservation if you move the NAS to another network or replace the router.
3. Alternative: a static IP on the NAS
In QTS, go to Control Panel > Network & Virtual Switch > Network > Interfaces > Configure, set IPv4 to static and fill in the IP address, subnet, gateway and DNS. QNAP's key points:
- Keep the NAS and the PCs on the same subnet.
- Place the static IP outside the router's DHCP pool, or reserve it on the router, to prevent conflicts.
4. Windows can't find the NAS by name after DNS or DHCP changes
QNAP describes this after an administrator changes DNS or DHCP settings: net view \\<NAS-hostname> times out, mapping a drive to the hostname fails, and the NAS no longer appears under Network in File Explorer. The cause QNAP gives is incorrect or outdated DNS/DHCP records, so the hostname resolves to the wrong IP or not at all. QNAP's steps:
- Verify DNS records: on your DNS server (or the router acting as DNS), confirm the A record for the NAS hostname points to the correct IP. If DHCP assigns DNS, make sure the DHCP scope options are updated.
- Flush the DNS cache on Windows: open Command Prompt as Administrator and run
ipconfig /flushdns. - Connect by IP as a temporary workaround, for example
net use H: \\<NAS-IP>\share. - Or edit the Windows hosts file (
C:\Windows\System32\drivers\etc\hosts, Notepad run as Administrator) and add a line with the NAS IP and a name, then map the share by that name. - Check SMB on the NAS: in Control Panel > Network & File Services > Win/Mac/NFS, make sure Microsoft Networking (SMB) is enabled and configured (SMBv2/v3).
- Restart the NAS properly from your username menu > Restart; QNAP says to avoid pulling the power plug unless absolutely necessary.
5. IP conflict after installing Container Station
QNAP describes a NAS on a corporate subnet that triggered an IP conflict after Container Station was installed: Container Station creates default container subnets, and one of them overlapped the LAN. QNAP's fix is to change the Container Station bridge subnet to a range that doesn't overlap, in Container Station > Preferences > Network Settings, apply, then restart Container Station.
When to stop and get help
QNAP gives two conditions to prevent IP conflicts: no other device may use the reserved IP, and a static IP belongs outside the router's DHCP pool. When you restart the NAS, use the Restart command in QTS rather than pulling the power plug.
Questions
Why does my QNAP NAS get a different IP after a reboot?
QNAP says DHCP assigns addresses dynamically and they can change when the lease renews or after a power outage. Bind the NAS MAC address to a fixed IP with a DHCP reservation on the router.
Should I use a static IP or a DHCP reservation on a QNAP NAS?
QNAP calls the DHCP reservation the preferred approach. A static IP set on the NAS also works if it is on the PCs' subnet and outside the router's DHCP pool.
Why can't Windows find my QNAP NAS by name after network changes?
QNAP says outdated DNS or DHCP records make the hostname resolve to the wrong IP. Fix the A record, run ipconfig /flushdns, or connect by IP.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.
- QNAP FAQ: NAS IP changes after reboot. How to keep a fixed NAS IP?
- QNAP FAQ: How do I ensure my QNAP NAS receives the same IP address with each DHCP lease renewal?
- QNAP FAQ: NAS Shared Folder Mount Failure After DNS or DHCP Changes
- QNAP FAQ: How to Change QNAP Container Station's Default Network to Fix IP Conflicts