NAS Codex › QNAP › QNAP NAS reports a fan error or a fan speed warning

QNAP NAS reports a fan error or a fan speed warning

QTS shows the system fan speed in Control Panel > System > System Status > Hardware Information, next to CPU usage, memory, disk temperature and power supply unit (PSU) status. QNAP's own documents cover three things that matter when a fan warning appears: the Smart Fan settings that decide how fast the system fans run, a known display issue on rack mount models where a PSU fan speed shows as "--" in red, and what to do about a failed fan on a QM2 expansion card.

Written against: QTS 5.1.x and QuTS hero (QTS 5.1.x help: Configuring smart fan settings; Monitoring system status and Resource Monitor; QNAP FAQs last modified 2022-10-18 and 2026-03-16). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

Open Control Panel > System > System Status > Hardware Information and read the system fan speed and temperatures. Then open Control Panel > System > Hardware > Smart Fan and check whether the fan speed is set manually; QNAP recommends Automatically adjust fan speed. On a rack mount model with QTS 4.5.2.1566 or earlier, a red "--" PSU fan speed is a known display issue that QNAP changed in later firmware. A failed fan on a QM2 card: if it is under warranty, contact QNAP Support or your reseller for RMA first.

1. Read the fan speed and temperatures

  1. Go to Control Panel > System > System Status.
  2. Open Hardware Information. QNAP says this screen shows CPU usage, memory, disk temperature, PSU status and system fan speed.
  3. For load, go to Control Panel > System > Resource Monitor. Its Overview summarizes CPU, memory and network usage and ongoing processes, and System Resource charts them over time.

Note which fan reports the problem and whether the temperatures are rising. That decides which of the sections below applies.

2. Check the Smart Fan settings

  1. Go to Control Panel > System > Hardware > Smart Fan.
  2. Look at how the fan rotation speed is set. QNAP notes that some NAS models let you adjust the system and CPU smart fans separately.
  3. Choose a setting and click Apply.

The options, as QNAP's QTS 5.1.x help describes them:

If the fan speed was set manually or to Quiet mode and the temperatures in Hardware Information are high, the automatic setting or Performance mode is the documented way to raise it.

3. Rack mount model: PSU fan speed shows "--" in red

QNAP documents a display issue on the TS-EC880U-RP and other rack mount models running firmware 4.5.2.1566 or earlier (builds before 20210202):

So on these models, update the firmware before treating a "--" PSU fan reading as a failed fan.

4. Failed or noisy fan on a QM2 expansion card

QNAP's FAQ covers the QM2-2P-344A, QM2-2P-384A, QM2-2P-244A, QM2-2S-220A, QM2-4P-384, QM2-2P2G2T, QM2-2P10G1TB and QMS-4S-240 (end of life). Its advice:

  1. Warranty first. If the card is under warranty, or you are unsure about compatibility, contact QNAP Support or your reseller for RMA options. QNAP warns that self-replacement may affect warranty decisions.
  2. Back up and plan downtime. Back up data on volumes or storage pools that use the QM2 card, schedule a maintenance window, then power off the NAS and unplug the power cord before removing the card.
  3. Match the fan. QNAP lists 60 mm x 60 mm, 8 mm high, 12 V DC, 0 to 5,600 RPM (plus or minus 10%), 4-pin connector, and says specifications may vary slightly between QM2 models and revisions, so compare with the original fan.
  4. Replace it using the same mounting points and connector, with the cable firmly connected and clear of other components.
  5. Validate. Power on, confirm the fan spins without abnormal noise, check NVMe SSD temperatures and system health in QTS or QuTS hero, and watch for temperature or fan warning events. QNAP says to monitor for at least 24 to 72 hours under a realistic workload.

QNAP explains the risks: a mismatched fan may not spin, may run at an unstable RPM or make abnormal noise, and too little cooling can cause overheating, thermal throttling or shorter SSD life even if temperatures look normal at first.

When to stop and get help

Back up before any hardware work. For a QM2 card fan, QNAP says not to power on the NAS before confirming the connector pinout and polarity, and not to assume a fan is compatible because it looks the same size.

Questions

Where do I see the fan speed on a QNAP NAS?

Go to Control Panel > System > System Status > Hardware Information. QNAP says it shows CPU usage, memory, disk temperature, PSU status and system fan speed.

How do I make QNAP fans spin faster?

In Control Panel > System > Hardware > Smart Fan, choose Performance mode, which runs the system fans at high speed, or set the speed manually with the slider.

Why does my QNAP rack NAS show the PSU fan speed as -- in red?

On rack mount models with firmware 4.5.2.1566 or earlier, the PSU does not report fan speed. QNAP says later firmware shows it in black as not available.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-18.