NAS Codex › Synology › Synology: The system found excessive and uncorrectable metadata errors

Synology: The system found excessive and uncorrectable metadata errors

DSM shows The system found excessive and uncorrectable metadata errors when it finds metadata errors on a Btrfs volume that it cannot repair. Synology explains that metadata holds file names, sizes and locations, which the file system uses to manage and find files. Its article is blunt about the fix: these errors cannot be repaired in place.

Written against: DSM 7.1 and above, and DSM Enterprise (Synology KB: excessive and uncorrectable metadata errors; How and when should I run a memory test; What can I do to prevent volumes from crashing). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

Synology says you cannot fix metadata errors caused by hardware problems, even after replacing the faulty hardware or running commands. The way out is: back up your data and package settings, remove the volume in Storage Manager > Storage, create a new volume, restore your data, and then check the drives, memory and shutdown history so it doesn't happen again.

Why the errors can't be corrected

Synology says Btrfs uses data and metadata checksums to protect integrity, and can detect silent data corruption and repair it through file self-healing. File self-healing only works on Btrfs volumes in RAID 1, RAID 5, RAID 6, RAID 10, RAID F1, RAID TP and Synology Hybrid RAID. When the corruption comes from these hardware problems, Synology says the resulting data and metadata errors are likely to be uncorrectable:

Synology adds that the damage varies from case to case. Left alone, it can stop the file system from reading and writing normally, accessing packages, repairing or expanding the volume, changing the storage pool's RAID type, or syncing and backing up data.

1. Back up, remove and recreate the volume

  1. Back up your data and package settings from the volume. Move the data to another storage device or volume, and use Hyper Backup to back up your package settings.
  2. Remove the volume: go to Storage Manager > Storage, click the icon at the upper right of the volume (in DSM Enterprise, select the volume and click Action), and choose Remove.
  3. Create a new volume.
  4. Restore your backed-up data to the new volume.

Synology notes that removing a volume only stops the related services for a while. It does not uninstall or erase DSM, because system data lives in the system partition on the installed drives, not in volumes.

2. Rule out the hardware causes

Synology's next step is to make sure the hardware is working: check for drive read/write errors, memory failure or incompatible memory modules, and improper shutdowns.

For memory, Synology's memory-test article says to use Synology Assistant (from the Download Center): click the icon at the upper right, tick Memory Test, select the NAS while its status is Ready, click Memory Test, and follow the wizard. The NAS reboots during the test and shows Performing memory test (x%); don't close Synology Assistant until it finishes. Synology recommends running the test three times. If it fails, you see "One or more errors have been found by the memory diagnostic test", which means the memory may be defective. Note that the status still shows Ready even after a failed test.

3. Stop it happening again

Synology says uncorrectable errors may cause the volume to crash, and its prevention article lists these measures:

When to stop and get help

Synology is explicit that these metadata errors cannot be fixed by replacing hardware or running commands. Synology's steps start with backing up the volume's data and package settings before the volume is removed.

Questions

What does excessive and uncorrectable metadata errors mean on Synology?

Synology says DSM found metadata errors on a Btrfs volume that it cannot repair, usually from drive read/write errors, faulty or incompatible memory, or improper shutdowns.

Can I fix uncorrectable metadata errors on a Synology Btrfs volume?

No. Synology says you cannot fix them, even after replacing hardware or running commands. Back up, remove the volume, create a new one and restore your data.

How do I test the memory on a Synology NAS?

Use Synology Assistant: tick Memory Test, select the NAS while it is Ready, and follow the wizard. Synology recommends running the test three times.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.