NAS Codex › QNAP › Time Machine backups to a QNAP NAS fail or crawl: what QNAP says to check

Time Machine backups to a QNAP NAS fail or crawl: what QNAP says to check

Your Mac's Time Machine backups to a QNAP NAS will not run, stop completing after a macOS update, or run very slowly. QNAP has three FAQs that cover these cases: the SMB setup Time Machine needs, a known problem with special characters after macOS 26 (Tahoe), and slow backups over Wi-Fi. This page puts them in order.

Written against: QTS and QuTS hero (QNAP FAQs last modified 2022-06-24, 2025-11-04 and 2026-01-12). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

In QTS (4.3.5 or later), enable Microsoft Networking and set the highest SMB version to SMB 3.0 or later. Mark the shared folder as the Time Machine backup folder in its properties, and give the backup user read/write permission. On the Mac, connect to smb:// plus the NAS's IP address, keep the folder mounted, then choose it in Time Machine. If backups stopped after macOS 26 (Tahoe), remove accented or non-Latin characters from the Mac's name and the folder names. If backups are just slow, try an Ethernet cable.

Step 1: set up SMB for Time Machine

QNAP's FAQ for Time Machine backups that fail over SMB gives this setup. The NAS must run QTS 4.3.5 or later. Log in to QTS as an administrator and open Control Panel.

  1. Go to Network & File Services > Microsoft Networking, tick Enable file service for Microsoft networking, and apply.
  2. Click Advanced Options, set Highest SMB version to SMB 3.0 or later, and apply.
  3. Go to Privilege > Shared Folders and find the shared folder you want to use for Time Machine.
  4. Click Edit Property, tick Set the folder as Time Machine backup Folder (macOS), and click OK.
  5. Click Edit Shared Folder Permission and give read/write permission to the user who will run the Time Machine backups.

Then on the Mac:

  1. In Finder, choose Go > Connect to Server, enter smb:// followed by the NAS's IP address, and click Connect.
  2. Select the Time Machine backup folder and click OK. Enter the user name and password to mount the folder, and keep it mounted.
  3. Open Time Machine, click Select Backup Disk, choose the Time Machine folder, and click Use Disk.

Backups stopped after updating to macOS 26 (Tahoe)

QNAP has a FAQ for Time Machine backups that fail to complete after updating to macOS 26 (Tahoe). It says this usually happens when the Mac's computer name, the backup file name, or the shared folder path contains special or non-ASCII characters, such as accented letters (ä, ø, é) or non-Latin characters (Chinese, Japanese, Korean). QNAP's workaround:

QNAP also recommends avoiding these characters in the Mac's name, backup folder names and shared folder paths, keeping both macOS and the NAS firmware up to date, and watching Apple's support announcements; it says to resume regular backups when Apple provides a fix in a future macOS update.

Backups are very slow over Wi-Fi

QNAP's FAQ on slow Time Machine backups describes a backup over Wi-Fi dropping to around 10 Mbps. It explains that Wi-Fi is typically slower and less stable than wired Ethernet for large transfers, and that the first Time Machine backup is often large and can take considerable time even over a wired connection. QNAP's steps:

  1. Connect the Mac to your network with an Ethernet cable (USB or Thunderbolt adapters can help) and run the backup again. If it is much faster, Wi-Fi speed is the limit.
  2. Once the first backup has completed, QNAP says later incremental backups over Wi-Fi should be much faster.
  3. If speeds stay slow, check for NAS firmware updates, make sure the NAS and the Mac are up to date, and restart the NAS and the router.

QNAP notes the first backup can take hours, especially over Wi-Fi. If performance is still poor over a wired connection, it says to review the NAS's network settings or contact QNAP support.

Summary of QNAP's checks

  1. QTS 4.3.5 or later, Microsoft Networking on, highest SMB version 3.0 or later.
  2. The shared folder marked as the Time Machine backup folder, with read/write for the backup user.
  3. On the Mac, connect over SMB, keep the folder mounted, then select it in Time Machine.
  4. After macOS 26: no accented or non-Latin characters in the Mac name or folder names.
  5. Slow: test over Ethernet; the first backup is the long one.

When to stop and get help

QNAP's macOS 26 FAQ suggests pausing Time Machine if many of your file or folder names use non-ASCII characters, until Apple releases a fix. It says to resume regular backups when Apple provides a fix in a future macOS update, and to keep both macOS and the NAS firmware up to date. If Windows PCs also cannot open the NAS's shared folders, see can't access QNAP shared folders from Windows.

Questions

How do I set up Time Machine on a QNAP NAS?

QNAP says to run QTS 4.3.5 or later, enable Microsoft Networking with the highest SMB version at 3.0 or later, mark a shared folder as the Time Machine backup folder, give the user read/write, then connect from the Mac over SMB and select the folder in Time Machine.

Why did Time Machine to my QNAP stop working after macOS Tahoe?

QNAP says backups may fail to complete after macOS 26 when the Mac's name, the backup file name or the shared folder path contains special or non-ASCII characters. Rename them using only letters, numbers, hyphens or underscores.

Why is Time Machine to my QNAP so slow?

QNAP says Wi-Fi is slower and less stable than Ethernet for large transfers, and the first backup is large. Try a wired connection; later incremental backups over Wi-Fi should be much faster.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.