NAS Codex › QNAP › QNAP QVR Pro camera not connecting or not recording
QNAP QVR Pro camera not connecting or not recording
QNAP has several short FAQs for cameras in QVR Pro and QVR Elite: a camera that fails to record, a camera that passed the test but still doesn't work as expected, Foscam cameras stuck on Connecting, and recordings that Recovery Management can't restore from the camera's SD card. This page puts their checks in one place.
Written against: QVR Pro and QVR Elite on QTS (QNAP FAQs last modified 2022-06-24, 2023-01-03, 2023-03-06 and 2024-04-11). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
In Camera Settings, check that the camera's Status is Connected. Then open Edit > Connection, confirm the IP, ports, account and password, and click Test. QNAP warns the test only checks basic details, so also confirm the selected model, give the camera account admin or root rights, and check whether DHCP gave the camera a new IP address.
1. The camera doesn't record
QNAP's checklist for a camera that fails to record on QVR Pro:
- Go to Camera Settings and check that the camera's Status is Connected.
- Go to Camera Settings > Edit > Connection and check that the camera IP, ports, account and password are all correct.
- In the same Connection tab, click Test and check that the camera configuration passes.
- Go to Camera Settings > Edit > Stream & Recording and check that Enable Recording is on and at least one recording stream is enabled.
- In Stream & Recording, check that the recording schedule is valid.
2. The camera passed the test but still doesn't work
QNAP says this applies when a camera is listed as compatible and passed the test when you added it, but still shows errors or doesn't work as expected in QVR Pro Client. Its note is the key point: the camera test only verifies basic information such as the IP, ports, username and password. It may not tell you whether the username has enough permissions, or whether you picked the right model. QNAP's checks:
- Model: the camera model must match the model selected in QVR Pro's settings page. Choose the correct model, or use the Generic ONVIF/RTSP/RTMP protocol instead.
- Credentials: make sure the camera's username and password are still correct, as they may have been changed.
- Account rights: the camera account needs enough privileges to control the camera's PTZ. Change the account's permission on the camera to root or admin and try again.
- IP address: check whether the DHCP server has given the camera a new IP address.
QNAP lists this FAQ for QVP series, QVR Elite, QVR Pro, Surveillance Station and VioStor series.
3. A Foscam camera is stuck on Connecting
For QVR Pro and QVR Elite, QNAP says some Foscam cameras use port 88 by default for both RTSP and HTTP after a firmware update, so the status stays on Connecting. The fix: edit the channel's Connection settings and set both Port and RTSP Port to 88.
4. Recordings missed during a network drop
QNAP says Recovery Management in QVR Pro and QVR Elite lets a camera restore recordings from its internal SD card when the network connection between the NAS and the camera was interrupted. Cameras with edge recording enabled are listed there. If a camera is missing from the list, or recovery doesn't succeed, QNAP's checks are:
- Edge recording or SD card recording is enabled on the camera.
- The camera profile in QVR Pro/Elite is set to ONVIF Profile T or ONVIF Profile S.
- The camera supports ONVIF Profile G for recovery. QNAP says QVR Pro/Elite detects this automatically when the profile is S or T.
- The stream is H.264 or H.265. QNAP says other formats such as MJPEG are not supported and recovery will fail.
- With the camera brand set to AXIS, recovery only works for H.264. Set the camera to ONVIF to recover H.265.
When to stop and get help
QNAP's test button confirms only that the IP, ports, username and password it was given are correct. A camera that passes it can still fail to record if the model is wrong or the camera account lacks admin or root rights.
Questions
Why is my QNAP QVR Pro camera not recording?
QNAP's checks: Status is Connected, the connection details are correct and pass Test, Enable Recording is on with at least one recording stream, and the recording schedule is valid.
Why does my camera pass the test but still not work in QVR Pro?
QNAP says the test only checks basic details. Confirm the selected model (or use Generic ONVIF/RTSP/RTMP), give the camera account root or admin rights, and check its IP.
Why is my Foscam camera stuck on Connecting in QVR Pro?
QNAP says some Foscam cameras switch to port 88 for RTSP and HTTP after a firmware update. Set both Port and RTSP Port to 88 in the channel's Connection settings.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.