NAS Codex › QNAP › QNAP HBS 3 RTRR backup to a remote NAS is stuck or fails

QNAP HBS 3 RTRR backup to a remote NAS is stuck or fails

QNAP's Hybrid Backup Sync (HBS 3) uses RTRR to back up from one QNAP NAS to another. When an RTRR backup job stays incomplete for a very long time, QNAP says the cause may be the network settings or the RTRR server settings. It recommends stopping the job manually and working through three checks before running it again. A separate FAQ covers jobs that fail with "Broken pipe".

Written against: HBS 3 v14 or later on QTS and QuTS hero (QNAP FAQs last modified 2023-05-22 and 2022-06-24; HBS 3 v21.x help: Configuring the RTRR server). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.

Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.

Fast Answer

Stop the job. On the local NAS, open HBS 3 > Storage Spaces > Remote NAS, edit the remote NAS, and click Detect Server and Speed Test. If that fails, open HBS 3 > Services > RTRR Server on the remote NAS: make sure it is enabled, set upload and download to Unlimited, and allow the local NAS under Network Access Approval. Then run the job again.

A. Check that the local NAS can reach the remote NAS

  1. On the local NAS, go to HBS 3 > Backup & Restore, click the RTRR backup job, and note the remote NAS name and IP address.
  2. Go to Storage Spaces > Remote NAS, select that remote NAS, and click the edit icon to open Edit Storage Space.
  3. Click Detect Server to check whether the remote NAS is reachable via RTRR. QNAP says a connection error here means you should check the RTRR service on the remote NAS (step C).
  4. Click Speed Test to check that the stored credentials work. If it fails because of incorrect credentials, QNAP suggests updating the RTRR credentials on the remote NAS.

B. Check the network settings

  1. On the local NAS, open the RTRR backup job's Edit a Backup Job window and go to Rules > Network. QNAP notes this setting only appears when the NAS has two or more network interface connections; if it isn't there, skip to running the job again.
  2. Select Default Route and click Save.
  3. Open Network & Virtual Switch > Network > Interfaces, note the IP addresses of all connected interfaces, and check that they are in the same subnet. QNAP's rule of thumb: the first three parts of the addresses should match. If they don't, you may need to reconfigure DHCP.
  4. Back in HBS 3, click Back Up Now. If the job still fails, go to step C.

C. Configure the RTRR server on the remote NAS

  1. On the remote NAS, go to HBS 3 > Services > RTRR Server and make sure the RTRR server is enabled.
  2. Set both Upload limit and Download limit to Unlimited.
  3. Check Network Access Approval. With Allow all connections, carry on. With Allow approved connections, click Add and enter the local NAS's IP address details, then click Apply.
  4. Back on the local NAS, open the job's Rules > Network, select Automatic (Optimized), click Save, and click Back Up Now.

What the RTRR server settings mean

QNAP's HBS 3 help describes the same page:

Job fails with "Broken pipe"

QNAP says a backup job may hang at 5% and then fail with Broken pipe when the source NAS runs HBS 3 and the destination runs HBS 2. If you can't install HBS 3 on the destination (the RTRR server), QNAP says to disable client-side encryption on the source NAS's HBS 3 backup job so the job can complete.

When to stop and get help

QNAP recommends stopping a long-running RTRR job manually before you change these settings. Its Broken pipe fix, for an HBS 2 destination that can't be updated, is to disable client-side encryption on the job.

Questions

Why is my QNAP HBS 3 RTRR backup job stuck?

QNAP says it may be the network settings or the RTRR server settings. Stop the job, run Detect Server and Speed Test, check the job's network rule, then check the remote RTRR server.

What does Broken pipe mean in a QNAP HBS RTRR backup?

QNAP says it can happen when the source runs HBS 3 and the destination runs HBS 2. If you can't install HBS 3 there, disable client-side encryption on the job.

How do I allow a NAS to connect to the QNAP RTRR server?

On the remote NAS, open HBS 3 > Services > RTRR Server. Under Network Access Approval choose Allow all connections, or add the local NAS's IP address.

Sources

Every fact on this page comes from the vendor documents below, opened on 2026-11-17.