NAS Codex › QNAP › Forgot your QNAP NAS password: what QNAP says to do
Forgot your QNAP NAS password: what QNAP says to do
You cannot sign in to your QNAP NAS because the password is forgotten. QNAP's FAQs split this in two: a regular user asks an administrator, and an administrator who has lost the admin password uses the reset button on the back of the NAS. This page covers both, the default password to sign in with afterwards, what the short and long presses change, and QNAP's steps if the default password still does not work.
Written against: QTS and QuTS hero, all QNAP NAS models (QNAP FAQs last modified 2025-10-15, 2026-09-22 and 2026-11-03). Last Updated: November 2026. Vendor menus and wording change between versions; if yours differ, follow the vendor page linked under Sources.
Before anything else: if the data on this NAS is not backed up somewhere else, copy it off first. Do not continue with any step on this page until you have.
Fast Answer
Not the administrator? Ask one to change your password in Control Panel > Privilege > Users. The administrator yourself? Press a straightened paperclip into the reset hole on the back of the NAS for 3 seconds, until one beep. User data and shared folders are kept. Then sign in as admin with the default password for your firmware: the Cloud Key on the label for QTS or QuTS hero 5.2.0 and later; the first adapter's MAC address, without colons and in uppercase, for 4.4.2 to 5.1.x; or admin for 4.4.1 and earlier. Do not hold the button longer: that is the factory reset.
If you are a regular user
QNAP says regular users cannot reset their own passwords. Contact the NAS administrator, who can change your password from the Control Panel without affecting any other account settings:
- The administrator signs in to QTS or QuTS hero and goes to Control Panel > Privilege > Users.
- They find your account and, in the Action column, click Change Password.
- They enter the new password, enter it again in Verify New Password, and click Apply.
QNAP notes that only an administrator can do this, and the new password must meet the system's complexity requirements.
If you are the administrator: the 3-second reset
QNAP's fix for a forgotten admin password needs physical access to the back of the NAS. Insert a straightened paperclip or pin into the reset hole and hold the button for 3 seconds, until you hear one beep. QNAP says this short press:
- keeps all user data and shared folders;
- resets the admin password to the default;
- resets the security level to "Low" (allow all connections);
- restores service binding and the system ports to their defaults;
- switches the network (TCP/IP) settings to DHCP, disables Jumbo Frame and VLANs, and sets Port Trunking to Active Backup on dual-LAN models.
QNAP's reset-button FAQ adds that the 3-second press resets the administrator password and network settings without affecting your data or other system settings, and that it is 3 seconds on both x86 (Intel/AMD) and ARM models.
The default password to sign in with
After the reset, sign in with the account admin. QNAP says the default password depends on the firmware version:
- QTS or QuTS hero 5.2.0 and later: the device's Cloud Key printed on the label, typically an 8-character alphanumeric string. QNAP's example: a Cloud Key printed as Q1234-5678 becomes the password
Q12345678, in uppercase with special characters removed. - QTS or QuTS hero 4.4.2 to 5.1.x: the MAC address of the first network adapter (Adapter 1), with the colons removed and all letters in uppercase. QNAP's example: 00:08:9B:AA:BB:CC becomes
00089BAABBCC. - QTS or QuTS hero 4.4.1 and earlier:
admin.
QNAP lists where to find these. The Cloud Key is on the sticker on the back or bottom of the chassis, or in the Quick Installation Guide. It is also shown in Qfinder Pro under Details, and in myQNAPcloud under Device Management > Device Details. If you cannot sign in to the NAS, QNAP says to power it off, remove all hard drives, M.2 SSDs and QM2 cards, power it on, and then open Details for the NAS in Qfinder Pro. The MAC address is on the chassis sticker and in the device information in Qfinder Pro.
Do not hold the button longer
A longer press is a different reset. QNAP's reset-button FAQ gives the time by platform: 15 seconds on x86 (Intel/AMD) models and 10 seconds on ARM models, held until you hear two beeps. It says this restores factory default settings and erases all system settings and app configurations; user data and shared files remain, but you must reconfigure the NAS. QNAP's forgotten-password FAQ describes the long press as 10 seconds, with one beep at 3 seconds and a second at 10, and warns that it deletes all shared folder configurations, which you then restore with the Backup/Restore function.
If the default password does not work after the reset
QNAP has a FAQ for this. It says that in some cases the default admin credentials may not work after a reset because of persistent configuration files or compatibility issues, such as an incomplete reset or system file corruption. Its fix uses SSH, and QNAP warns that removing or reinserting drives incorrectly can risk data loss, so note the drive order and do not initialize the NAS. If you are not familiar with SSH, QNAP says to contact QNAP Tech Support.
- Power off the NAS and remove all drives.
- Power it on with no disks inserted, and wait for a short beep followed by a long beep.
- Run Qfinder Pro to find the NAS and note its IP address. If you are asked to initialize the NAS, click No.
- Without powering off, reinsert the drives in their original order.
- Connect over SSH with the default admin credentials and run
ls /sbin/hal_app. If it reports "No such file or directory", the NAS is a legacy model; if it completes silently, it is a HAL model. - On a HAL model, run
storage_util --sys_startup, thenpasswdand follow the prompts to set a new admin password, thenreboot. On a legacy model, QNAP gives a different command sequence (starting withconfig_util 1andstorage_boot_init 1, then copying the default passwd, shadow and group files) beforereboot.
QNAP says the admin password is updated after the reboot.
When to stop and get help
Press for 3 seconds and let go at the first beep. Holding until the second beep is the factory reset: QNAP says it erases all system settings and app configurations and deletes shared folder configurations, although data on the disks is kept. For the SSH route, do not initialize the NAS and put the drives back in their original order. If Qfinder Pro cannot find the NAS, see Qfinder Pro can't find your QNAP NAS.
Questions
How do I reset a forgotten QNAP admin password?
QNAP says to press and hold the reset button on the back of the NAS for 3 seconds until one beep. This resets the admin password and network settings to default and keeps all user data and shared folders.
What is the QNAP default password after a reset?
QNAP says the account is admin. The password is the Cloud Key on the label for QTS or QuTS hero 5.2.0 and later, the first adapter's MAC address without colons in uppercase for 4.4.2 to 5.1.x, and admin for 4.4.1 and earlier.
Does resetting a QNAP NAS delete my data?
QNAP says the 3-second reset keeps user data and shared folders. The longer factory reset (10 or 15 seconds by platform) erases system settings and app configurations but keeps user data and shared files.
Sources
Every fact on this page comes from the vendor documents below, opened on 2026-11-17.